In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass of the car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What input force (in N) is needed to support the car and the output plunger when the bottom surfaces are at the same level?

In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass of the car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What input force (in N) is needed to support the car and the output plunger when the bottom surfaces are at the same level?

Name: QUESTION 10In a hydraulic car lift, the input piston has a radius of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QUESTION 10In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass ofthe car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What inpu

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.141RP: The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels are 16 ft on the upstream side and zero on the downstream side. For water, use =62.4lb/ft3.
The plunger of the hydraulic lift in a gasoline service station has a diameter of 1 inch. It is operated by a compressed air (density = 63 kg/m3) from the tank in which the pressure is 9.315 x 105 pascals. The output piston and the rack on which the car rests are 2 feet lower than the input plunger and together weigh 1,336.33 newtons. What is the weight of the heaviest car that can be lifted if the output piston has a diameter of 1 foot? Assume 80% efficiency of the machine.
The hydraulic jack is filled with oil (S-0.9). Neglecting the weight of the two pistons, what force F on the handle is required to support the block mass of m=222 kg for this design? 6 cm diameter 5 cm 30 cm 3 cm diameter
The total pressure force of a square plate is 25 kN, placed vertically in water so that the center of the plate is 1.5 m below the free surface. Determine the size of the plate and the depth of center of pressure. The above square plate is taken out of the water which weighs 370.5 N in air and 180.3 N in water of specific gravity 0.99. Find the volume and specific gravity of the square plate. Draw a neat sketch.
1. Consider a conic reservoir of unit depth that is initially filled with water at the height of h = 200 mm. A rigid cuboid block, with dimensions of 10 cm x 5 cm x 3 cm, is then dropped into the water. When the equilibrium state is reached, the block floats on the water's surface, as shown in the figure. If the specific gravity of the block is 0.5, determine the change in the free surface position of the water, i.e., Ah, in mm. %3D Hint: You can calculate the volume of liquid inside the conic reservoir with a unit depth in terms of the liquid height as V = th³/3. Ah block water water
The hydraulic jack in Fig. is fi lled with oil at 56 lbf/ft 3 .Neglecting the weight of the two pistons, what force F onthe handle is required to support the 2000-lbf weight forthis design?
Ex. 5. A weight lies on a piston with a radius r₂ = 1.0m. Determine the for- ce F₁ applied to the piston with radius r₁ = 20 cm if the hydraulic jack is in a balance. The jack is filled by an oil with po = 850 kg/m³. A mass of we- ight is m 1000 kg. Neglect the mass of the pistons. (Ans. F₁ = 392.4 N) = F₁ 0.3 m m oil
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
In the setup seen in the image, an oil tank's central circular opening is sealed off by a solid cone. At the bottom of the tank is a mercury-filled U-tube manometer. As of the moment depicted, a. 20 cm C. 100 cm I I 35 cm Pressurized A air solid cone B с What is the pressure at the bottom of the tank? b. What is the pressure of air trapped in the tank? How far from the oil-air interface is the location of the imaginary oil surface? Oil (SG = 0.8) 5 cm 30 cm 50 cm open !!! 30 cm Hg (SG = 13.6)
The hydraulic jack is filled with oil (S=0.9). Neglecting the weight of the two pistons, what force F on the handle is required to support the block mass of m3D224 kg for this design? 6 cm diameter 5 cm 30 cm F 3 cm diameter Oil
Q3: What force is required to bal ance the weight of the cylinder if the weight of the plung er is negligible. - Plunger arca - Sis Cylinder Weight= 10,000 Ib Cross-sectional arca = 500 in %3D 15t Oil (sg = 0.78)