In a temperature measurement system ,the element A receives the temperature value and produces millivoltage as the output. This output is given to an element B. The element B increases the millivoltage value into voltage value. Then it is given to element C. The element C converts the analog voltage into Digital value .The element D displays the output. Identify the elements A, B, C and D used in the above mentioned temperature measurement system.

In a temperature measurement system ,the element A receives the temperature value and produces millivoltage as the output. This output is given to an element B. The element B increases the millivoltage value into voltage value. Then it is given to element C. The element C converts the analog voltage into Digital value .The element D displays the output. Identify the elements A, B, C and D used in the above mentioned temperature measurement system.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

What is CEMF?
In a temperature measurement system the element A receives the temperature value and produces millivoltage as the output. This output is given to an element B. The element B increases the millivoltage value into voltage value. Then it is given to element C. The element C converts the analog voltage into Digital value .The element D displays the output. Identify the elements A, B, C and D used in the above mentioned temperature measurement system.
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
a) Name of the Circuit? (Assume Silicon Diodes) , 4:1 D b) Find the peak input voltage to the 120 V rms diodes. R 1.0 k D2 c) Find the average output voltage? d) Find the DC current? d) Find the Peak Inverse Voltage of the diodes? e) Draw the output waveform. eetee
la) Name of the Circuit? (Assume Silicon Diodes) 4:1 D b) Find the peak input voltage to the 120 V rms diodes. RL 1O kn c) Find the average output voltage? d) Find the DC current? d) Find the Peak Inverse Voltage of the diodes? e) Draw the output waveform. 00000
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 V and V2=9 V. R DZ D1 Vin Vout v2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 v and V2=8 V. R DZ D1 Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform Windows hui
What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (236 v), and true form foctor of input waveform is (114). *
CIRCUIT DIAGRAM : D1 IÑ4001 AC Source RL 1K Q VOUT PROCEDURES : 1. Construct the half-wave rectifier circuit as shown. 2. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the formula: 3. 4. Vp-p Vp-p P-P VRMS 2.828
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at the output is: O A. 73 W O B. 18 W C. None of the other choices are correct D. 36 W O E. 146 W