In a three-phase balanced wye-wye system, the source is an abc-sequence. Van =120/60° V rms. The per phase impedance of the load is 12 +j1602. If the line impedance per phase is 0.8 + j1.402, find the magnitude of the phase voltage at the load. Select one: O a. 120 V O b. 135.1 V O C. 8.965 V O d. 111.1 V

In a three-phase balanced wye-wye system, the source is an abc-sequence. Van =120/60° V rms. The per phase impedance of the load is 12 +j1602. If the line impedance per phase is 0.8 + j1.402, find the magnitude of the phase voltage at the load. Select one: O a. 120 V O b. 135.1 V O C. 8.965 V O d. 111.1 V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

In a balance three-phase system, the source has an abc-phase sequence and is connected in delta. The line connecting the source to the loads has an impedance of 1 + j2 № per phase. There are two loads connected in parallel. Load 1 is connected in wye, and the phase impedance is 4 + j2 2. Load 2 is connected in delta, and the phase impedance is 12 + j9 №. The current lab in the delta load is 16/45° A. Find the phase voltages of the source and the line currents. Write your values in polar form.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
The magnitude of the phase voltage of an ideal balanced three-phase Y-connected source is 125 V. The source is connected to a balanced Y-connected load by a distribution line that has an impedance of 0.1 + j0.8 02/0. The load impedance is 19.9 + j14.20/0. The line current laA is: Select one: O a 3-j4A O b. 14-j3 A O c. None of these Od 4-3 A The line current lax in the single-phase equivalent circuit (Y-A) for a balanced three-phase circuit Inegative sequence) is 35/3220° A. Then the phase current lag is:
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
on A balanced three-phase source serves two loads: Load 1: 36 KVA at 0.8 pf lagging Load 2: 18 kVA at 0.6 pf lagging The line voltage at the load is 208 V rms at 60 Hz. Find the power factor at the load. Select one: O a. 0.74 lag O b. 0.6 lag Oc. 0.8 lag
A three-phase source delivers a power of 30KVA at a lagging power factor of 0.6 to a three-phase balanced load through a line with an impedance of 0.1+j0.3 0/p. The phase voltage of the source is 200 Vms, what is the line current? Select one: O a. 60 + j8 Arms Ob. 150 Arms O c. 30-40j Arms O d. 6- j8 Arms TOSHIBA
A balanced delta connected load has an impedance of (60 +j45) ohm per phase. The load is fed through a line having an impedance of (0.8 +j0.6) ohm per phase. The phase voltage at the terminals of the load is U =480V. The phase sequence is positive.N.B: Use UAB as the reference.a- Calculate the three phase currents of the load.b-Deduce the three line currents I.c- Construct the a-phase equivalent circuit of the system.d- Calculate the three line-to-neutral voltages at the sending end of the line e-deduce the threee to line voltages
An abc-phase sequence balanced three-phase source feeds a balanced load. The system is connected wye-wye and Van is reference phase. The line impedance is 0.5+ j0.2 02, the load impedance is 16+j102, and the total average power absorbed by the load is 1836.54 W. Determine the power lost in the line. Select one: O a. 57.47 W O b. O C. O d. 1836.54 W 0.5 W 517.26 W Oe. None of these
QUESTION 3 Find the magnitude of the phase voltage of a wye-delta system that has a balanced load of 1000 and a load current of 2.6A RMS. O 40V RMS O 100V RMS 60V RMS 150V RMS
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Time left 1:25:45 In a three-phase balanced delta-delta system, the source has an abc-phase sequence. The line and load impedances are 0.3j0.2 and 9+16 ohms respectively. If the phase cument in the load is 11.49 +19.64 Arms, find the magnitude of the phase voltages of the load Select one: O a. 103 O b. 178.5 Oc 56.25 O d. 162.25
5. In the network below, EA = 230Z0° V. and the phase sequence is acb. Find the line currents and the phase currents. A a EAN 40+j30 a 30+j40 O ECN b 50-j30 a B.