In the below figure, the capacitor is initially uncharged. At t = 38 us after the switch is closed, the instantaneous capacitor voltage is 5.7 V. Determine the value of R given that C = 2.9 µF. The result should be in Ohm. Calculate Answers to 2 decimal points 10 V. R www

In the below figure, the capacitor is initially uncharged. At t = 38 us after the switch is closed, the instantaneous capacitor voltage is 5.7 V. Determine the value of R given that C = 2.9 µF. The result should be in Ohm. Calculate Answers to 2 decimal points 10 V. R www

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 7PP: A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a...

See similar textbooks

Related questions

Q: S. What are the most popular type of nuclear power plant, used for generating electricity? Which…

A: The most popular type of nuclear power plant used for generating electricity is the pressurized…

Q: A finite line charge located at (0, y, 0)m, where a≤y≤b , has a line charge density of ρL = ycosy…

A: Given,At (0, y, 0)m, a finite line charge is located.where a≤y≤b.The line charge density…

Q: Determine the DC parameters for this BJT circuit. Μ +20 V R₁ 150 ΚΩ R₂ 20 ΚΩ Rc · 12 ΚΩ hFE = 200 RE…

Q: Draw the corresponding output waveform of the double diode partial limiter below using simplified…

A: In this question We need to draw the corresponding output waveform. We know forward bias voltage…

Q: Wouldnt the peak voltage in the secondary half be 1/3 x 1.414 x 120? 56.56V divided by 2 28.28…

A: The given circuit is a center tapped full wave rectifier and the required parameters can be…

Q: The gap in the circuit seen in (Figure 1) will arc over whenever the voltage across the gap reaches…

A: The required beta can be calculated by connecting the test voltage or test current to the open…

Q: A 146 -km long, 54 Hz, single-phase, 2-wire, transmission line is composed of 20-mm diameter solid…

A: The inductance per unit length of a single-phase, 2-wire transmission line can be computed using the…

Q: P₂: Design the Phase shift oscillator to oscillate at f. = 22.5KHZ. The minimum resistance to be…

A: Given data Frequency of oscillation; fo=22.5 kHz Minimum resistance value; Rmin=10 kΩ Expression for…

Q: How do you 9777pU? O you convert 3 2.26hv in to

A: To convert 32.26 kV (kilovolts) to 0.9777 pu (per unit), you need to know the base voltage of the…

Q: r²+²+ -10-3 For the signals studied in problem 6-3 above, we can approximate the bandwidth of the…

A: Assumption for the message signal ωc=2π×10-7 rad/sec Kf=104π Kp=25π fc=10 MHz From the waveform,…

Q: In this question,You have to find T.F [Eo(s)/Ei(s)] ,Please show all the Work In handwritten format.…

A: In this question we need to find transfer function of the given circuit.

Q: Exercise 2: For the transistor circuit shown answer the following: a) What is the name of the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A system is described Y(n) + 0.5 y(n-1) the Solution - Determine is described by the difference n 2…

Q: 11 The intrinsic impedance of a medium is given by impedance in free space is: Hint: -8.854x10 and…

A: Given: μ0=4π×107H/m ∈0=8.854×10-12 η=μ∈Ω

Q: Given the following impedances: X1-j0.15 X2-j0.15 XO=j0.2 Find: 1) Three phase fault 2) Single Line…

Q: (d) X(s) = S(S-1) S4-1 (e) X(s) = (f) X(s) = se-its s²+1 (s+2)²(s+4)

Q: 1. Sketch the root locus for the unity-feedback system shown below. Find the value of K when (1) the…

A: Given: Gs=54Ks+6s+9

Q: can you please show the solution,Thankyou

Q: Question 2: Draw the electrical diagram that shows delivering 3 phase electricity to the house,…

A: Three-phase power supply is a type of electrical power transmission that uses three alternating…

Q: 3. Convert this decimal code to binary then to hex and then to ASCII 68 117 110 110 32 105 115 32 70…

A: Convert each decimal number to binary manually: 68 = 01000100 117 = 01110101 110 = 01101110 110 =…

Q: A 100 MVA, 50 Hz generator feeding power through a double circuit transmission line with initial…

A: Given: Rated MVA capacity of Machine, G = 100 MVA System frequency, f = 50 Hz Initial rotor angle,…

Q: In the circuits depicted in Fig., assume Iin= lo cos wt, where Io is relatively large. Plot Vout as…

A: For the given circuits,The value of input voltage is,Iin=I0 cosωt,Where,I0 is relatively large.

Q: A uniform sheet charge with ρS = (1/3π) nC/m2 is located at z = 5 and a uniform line charge with ρL…

Q: 1. Solve for IL for the circuit shown by: (a) Thevenin s Theorem; (b) Norton s Theorem. j2s2 200…

Q: CLK X Y Z X R Y Z Consider the following digital logic design that has a D-FF in it: D D CLK F D…

Q: mmc UD D in ne IN T זרזבט רזבײַזומ ממזונור מרמנcבסי Q.94 For a 3.6°, 2-o bipolar stepper motor, the…

A: Given- A 3.6o, 2-ϕ bipolar stepper motor- Stepping rate=200 steps/second, To Find- The rotational…

Q: E(t) 240, 0sts 50 t> 50 is applied to an LR-series circuit in which the inductance is 30 henries and…

A: Based on the bartleby guidelines solved first question kindly repost the remaining questions as…

Q: VBB RB www Voc +₁. Rc IR

Q: Given the function f(A,B,C,D) = A'B'C + AB'C + ACD + A'B'CD' +AB'CD' 1. Optimize the expression…

A: According to the given questions, we need to find the POS expression of the given Boolean function.

Q: find transfer function Passive filter Low Pass filter Highfass filter d volus Band pass filter Band…

A: Need to find transfer function Passive filter a. Low Pass filter b.Highpass filter c. Band pass…

Q: a. b. C. Please find y[n] = x[n] * h[n] with following x[n] and h[n]. x[n] = 8[n] + 28[n − 1] + 38[n…

Q: An ideal op-amp circuit is shown above, with dc supply Vcc = -Vcc = 12V. Assume that vs = 3V, R1 =…

A: Answer: given that an inverting operational amplifier input voltage VS = 3 V resistances R1 = 2…

Q: 5. For the circuit shown below, find the branch currents 11, 12 and 13 using mesh analysis. 450 62…

Q: Consider the circuit shown below, containing two bulbs and a capacitor (initially uncharged…

Q: 4.27 Design an op-amp circuit that performs an averaging operation of five inputs v₁ to v5.

A: The required circuit can be designed with the help of summing amplifier and the averaging function…

Q: 12. Find to in the circuit below using nodal analysis: 192 www 802 10 100 V 4 A 13. Using nodal…

A: In these questions We need to determine the all unknown parameters. We are solving these problems…

Q: How much will it cost to run an electric motor for 10 days if the motor draws 15 A of current from…

A: In this question We need to determine the cost of the electricity. We know Energy E= power × time…

Q: Discuss the prime mover and the conversion of power energy for thermal station

A: We need to discuss the prime mover and the conversion of power energy for thermal station.

Q: Having the below j5 -j10 Nodal-Admittance Equation: j0.8 j1 j2.5 j2.5 -j6.8 j5 j0.8 j2.5 -j4.55 jo…

Q: For the system below, G(s) = 0.04 s²+0.02s +0.04 The settling time is equal to s. Express your…

Q: Explain any two Passive transducers with neat diagram. Note: don’t write by hand diagrams should be…

A: We need to write about passive transducer The passive transducer is a transducer, which creates…

Q: 2. Electromagnet Fursday's Blucrum Lab (207) Fie Options Halp Bar Magnet Pickup Coll Electromagnet…

A: Faraday's law This law states that the rate of change of magnetic flux in the circuit is responsible…

Q: 500 V + 8 Ω 10 Α 30 Ω 5.2 Ω §12 Ω a b

Q: 11 ĐVL) I (t) IF ан In the Above porobuem you have to Hind Tramber funktion. B/u output I cz) &…

Q: 3.7 Assuming that the diodes in the circuits of Fig. P3.7 are ideal, find the values of the labeled…

A: The required parameters can be calculated based on the conduction of both the diodes in the circuit.…

Q: D only hurry please~!!

A: 6) two transfer function with pole zero plot given , and the dc gain of the system H1(0)=0.5 and…

Q: If the current i(t) for an element is -6.9t A for t ≤0, and 5.5t A for t > 0. Find: (a) i(-4.8) (b)…

Q: A logic function is expressed by the equation = 0.1.8.9.4. Plot the the values on the K-map below…

A: I have provided the k - map and simplified the expression below. Please go through it

Q: Derive the following equation ICEO= (1+β )ICBO

Q: X D Q ко D Q OA OB A 0 0 0 OO 0 1 1 1 1 BOOT TOOT 0 0 1 1 1 0 0 XO 1 1 0 1 0 1 0 1 Next State A B

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

In the below figure, the capacitor is initially uncharged. At t = 38 us after the switch is closed, the instantaneous capacitor voltage is 5.7 V. Determine the value of R given that C = 2.9 µF.
The result should be in Ohm.
Calculate Answers to 2 decimal points
10 V
R

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
List the five capacitor replacement rules.
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
What is the minimum AC voltage rating of each capacitor in Question 11?
Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow. XC=12fCC=12fXCf=12CXc Capacitance XC Frequency 38 F 60 Hz 78.8 400 Hz 250 pF 4.5 k 234 F 10 kHZ 240 50 Hz 10 F 36.8 560 nF 2 MHz 15 k 60 Hz 75 nF 560 470 pF 200 kHz 6.8 k 400 Hz 34 F 450
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
In a pure capacitive circuit, does the current lead or lag the voltage?