in the curcuit shown in the figure , the S switch is closed at t = 0 and the capacitors, which are completely empty, begin to fill. Here E = 20 V , C = 4uF and R = 30 ohm. a) what is the time constant of the circuit , T in units of microseconds? b)when t=T , what is the total charge , in units of microcloumb accumulated in the capacitors

in the curcuit shown in the figure , the S switch is closed at t = 0 and the capacitors, which are completely empty, begin to fill. Here E = 20 V , C = 4uF and R = 30 ohm. a) what is the time constant of the circuit , T in units of microseconds? b)when t=T , what is the total charge , in units of microcloumb accumulated in the capacitors

Physics for Scientists and Engineers with Modern Physics

10th Edition

ISBN:9781337553292

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter43: Nuclear Physics

Section: Chapter Questions

Problem 44P

See similar textbooks

Similar questions

Reclung.c A on ri gle Figure 1 2. The circuit shown above is constructed with two 6.0 V batteries and three resistors with the values shown. The currents 1₁, 12, and 13 in each branch of the circuit are indicated. 2 GEOMETRY AND TRIGONOMETRY Circle A = ²² C = 2πr Cy.inder bh - re Rectangular Solid Vlh Sphere 1. Using Kirchhoff's rules, write, but DO NOT SOLVE, equations that can be used to solve for the current in each resistor. ii. Calculate the current in the 200 9 resistor. iii. Calculate the power dissipated by the 200 2 resistor. V = ar²l S.. Figure 2 The two 6.0 V batteries are replaced with a battery with voltage & and a resistor of resistance 50 2, as shown above. The voltmeter V shows that the voltage across the 200 £2 resistor is 4.4 V. (b) Calculate the current through the 50 2 resistor. (c) Calculate the voltage & of the battery. V=² S = 4; 7² Rig Triangle 2 +6² = c² sin = COS== tan 8 = OJA b C 2m. a b 6.0 V 7,4 & A - area C=circumference h-hei £= le L W = IUL r=fuu.0…
4. The Voltmeter connected across load (Bulb) will measure [Choose any one answer] Potential Difference + 5. A constant current source supplies a electric current of 200 mA to a load of 2kn. When the load changed to 500, the load current will be O700mA O8A O12A O9mA 6. To measure A.C voltage the knob should be at
av 322 3352 1. What is the total Current? 2. What is the VOltage across the 2 onm resistor? 3. What is the curent through the 3n resistor? 4. What is the power suppued by the batiery
Change the polarity of the Voltage Source into. GermaniumD Vo 1N5818 R1 100 V1 .dc oct V1 0 3 1 What is the Peak Value of Vo of the schematic above in milliVolts? 3.
In the saturation region (I-V characteristics) of JFET the value of D18 ssmemanmnssnes at specific (VGS = * .negative voltage ) a. b.c.d a: constant O b: zero O c: maximum O d: Bothaandc O
MC tres!) oftand Q3/A- Design a voltage regulator circuit by using variable input voltage. Use the following information in your design: Izk = 0.25mA, PD(max) =1W, voltage Zener Vz-10v, the resistance R-22002. aqd pul rosmo B-What is a Zener diode? roapsula
1. Calculate the potential due to a dipole as shown in the figure at positions A and B in millivolts. 2. What would be the potential at Bif the distance from the dipole center to B is doubled,. 3. What would be the potential at A if the intensity of the current source is doubled. +2mA B =12em F 10mm 20 degree 90 degree r95 cm A. Resistivity = 75 Ohm-cm -2mA Dipole
Q1. A voltage regulator circuit is given below with Vz of Zener diode 9V and 100mA is the total current. a. Determine the minimum and maximum input voltages (Vin) that can be regulated by the given circuit. b. Determine the minimum value of load Resistance, RL suitable for Zener diode with Izk=15mA. R 470 N IT 100 mA Vin RL 500 Ohms
5. A 250-volt electrical heater is used to warm 3Li/hr of water from 19°C to 98°C. Assume heat conversion loss of 25% of the total heat supplied, how much current in amperes must be supplied to this heater. Derive with the formula below, show the cancellation, explain the step by step and DRAW a free body diagram/figure. refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.
The current through the filament in an Xray unit can be AC or DC. True O False Question 46 The voltage between the anode and the cathode inside an X ray unit can be alternating or direct. True 2 False
geTef-Glogle Chrome modiguia/amempt.pholattempte1867768cmid=3903 E Physics II (CRN: 50010) Consider the long (L> b) cylindrical shell of inner radius a = Rand outer radius b= 3R as shown in the figure. The current I- 4 A is uniformly distributed over the cross section of the wire. Here R= 1.3 cm. What is the magnitude of the magnetic field, in units of microtesla, at distance 2R? (Ho = 4x x 10 7 T - m/A) Answer Next page
5. Compute for the individual values and the total values of the voltage, the current, and the resistance of the series circuit here. R, = 100 A VOLTAGE, CURRENT, RESISTANCE, V Vs = 12v R2= 200 R3 =300 6. Draw a series circuit connecting a battery and four resistors with a total resistance of 15 Q. The total current in the circuit should be 3 A. 7. Compute the individual values and the total values of the voltage, the current, and the resistance of the circuit here. IT VOLTAGE, CURRENT, RESISTANCE, 12 V V, = 24v R1 R2 R3 R1=102 R2 200 R3 =300 70 Property of and for the exclusive use of SLU. Reproduction, storing in a retrieval system, distributing, uploading or posting nline, or transmitting in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise of any part of this document, without the prior written permission of SLU, is strictly prohibited. 2021.03.08 09:52