In the laboratory test on a clay sample ofthickness 25mm, drained at top only, 50%consolidation occurred in 11 minutes. Assume= 0.197, T = 0.405. Find the time requiredfor the corresponding clay layer in the field of 3mthick and drained at top and bottom to undergo50% consolidation. Also, find the time required toundergo 70% consolidation.TE%3D7050

Answered: Image /qna-images/answer/f00d8342-1f75-4deb-a33b-f3584ebb8f1e.jpg

Answered: In the laboratory test on a clay sample…

Engineering

Civil Engineering

In the laboratory test on a clay sample of thickness 25mm, drained at top only, 50%

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.20P

See similar textbooks

Similar questions

Find the C, and the "apparent" OCR for a superficial clay stratum that is 4m thick. The water is at the surface. A sample of the clay has a water content of 27.9%, and a specific gravity of 2.65. An oedometer test showed the following results: Voids Ratio 0.736 0.733 0.73 0.675 0.638 0.6 Vertical Effective Stress 15 28 60 230 480 930
A given saturated clay is known to have effective strength parameters of c' = 10 kPa and = 28°. A sample of this clay was brought to failure quickly so that no dissipation of the pore water pressures %3D could occur. At failure it was known that o KPa, o = 10 KPa and = 20 kPa. %3D (a) Estimate the values of o, and oz at failure (b) Use the Mohr circle to illustrate the effective stress and total failure stress.
A consolidated undrained triaxial test was performed on a normally consolidated clay with a critical state friction angle of 230. After an initial isotropic consolidation at a cell pressure of 50 kPa, drainage was turned off, the cell pressure was increased to 85 kPa, and the sample was loaded to ultimate conditions. A pore pressure of 55 kPa was measured at ultimate state. What value of major principal total stress was measured at the ultimate state?
5. A consolidated, undrained triaxial test is being caried out on a normally consolidated clay where c = 0 and 41= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
Following are the results of a consolidation test on a sample of undisturbed clay obtained from the field. Pressure ơ' (kN/m²) Final Height of Specimen (mm) 24 10 23.78 20 23.30 50 22.22 100 20.58 200 19.04 400 17.52 800 16.31 17.75 The height of the specimen at the beginning of the test was 24 mm and the area of specimen was 50 cm? volume of specimen was 120 cm³. The mass of dry specimen was 180.4 g. Gs= 2.68. 1. Plot the e-log ơ' curve, 2. Using Casagrande's method, determine the preconsolidation pressure. 3. Calculate the compression index, Cc
5. A consolidated, undrained triaxial test is being carried out on a normally consolidated clay where c - 0 and p'= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?
1. The pressure versus void ratio data determined from a consolidation test on an undisturbed clay specimen are as follows: Applied Pressure (kPa) 20 40 80 160 320 640 1280 320 80 20 0 Void Ratio 0.953 0.948 0.938 0.920 0.878 0.789 0.691 0.719 0.754 0.791 0.890 (a) Plot this pressure versus void ratio data on a semi-logarithmic graph. (b) Determine the equations for the virgin compression curve and for the rebound curve for unloading starting at 1,280 kPa. (c) What are the corresponding compression and recompression indices for this soil? (d) Estimate the stress to which this clay has been preconsolidated. (After A. Casagrande.)
A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, E₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (su). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.
During the shearing phase of a CU test, the void ratio of a NC consolidated clay specimen will: 1decrease. 2could increase or decrease. 3remain a constant. 4increase.
A 75 mm diameter clay specimen was consolidated in an oedometer under 200 kPa. At the end of consolidation, the void ratio is 0.863 and the specimen thickness is 18.51 mm. When the stress increment of 200 was added to the current vertical stress of 200 kPa, the specimen consolidated to a thickness of 17.56 mm. Assuming that the clay was normally consolidated under the vertical stress of 200 kPa, find the a) coefficient of volume compressibility in (MPa)^-1 and rounded to the 3rd decimal place.b) and the compression index of the clay rounded to the 2nd decimal place.
Please give me right solution according to the question. In a triaxial test on a saturated clay, the sample was consolidated under a cell pressure of 160 kPa. After consolidation the cell pressure was increased to 350 kPa, and the sample was then failed under undrained condition. If the shear strength parameters of the soil are c’ = 15.2 kPa, ϕ’ = 26°, B = 1, Af = 0.27, determine the pore pressure at the failure.
The void ratio of a clay sample A decreased from 0.572 to 0.505 under a change in pressure from 122 to 180 kN/m2. The void ratio of another sample B decreased from 0.61 to 0.557 under the same increment of pressure. The thickness of sample A was 1.5 times that of B. Nevertheless, the time taken for 50% consolidation was 3 times larger for sample B than for A. What is the ratio of coefficient of permeability of sample A to that of B? a. 9.8:1 b. 6.4:1 c. 12:1 d. 8.7:1