Please help me to solve the two questions. Thanks Task 1In the process of chargingaccumulatorthepiston(diameter D=120 mm andmass m=0,6 kg) movedupward to a height of x=120mm. Charging pressure isp=10neglected.MPа.FrictionisDeterminethe requiredspring constant c.Task 2The total weight of the plunger and load is 30 kN, the plungerdiameter is D=200 mm. Neglecting friction in the accumulatordetermine the oil pressure in its chamber.区DE

Answered: Image /qna-images/answer/ef2498a5-ae0b-4087-a213-2afb403cd648.jpg

In the process of charging the accumulator piston (diameter D=120 mm and mass m=0,6 kg) moved upward to a height of x=120 mm. Charging pressure is p=10 MPa. neglected. Determine the required spring constant c. Friction is Task 2 The total weight of the plunger and load is 30 kN, the plunger diameter is D=200 mm. Neglecting friction in the accumulator determine the oil pressure in its chamber.

In the process of charging the accumulator piston (diameter D=120 mm and mass m=0,6 kg) moved upward to a height of x=120 mm. Charging pressure is p=10 MPa. neglected. Determine the required spring constant c. Friction is Task 2 The total weight of the plunger and load is 30 kN, the plunger diameter is D=200 mm. Neglecting friction in the accumulator determine the oil pressure in its chamber.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hydraulic brake system is shown in the figure below. The radius of the input piston is 1.20cm and the radius of the output plungers is 3.40cm. The lengths associated with the lever arms of the brake pedal are L1 = 4.70cm and L2 = 13.0cm. Assume that the force delivered by each output plunger in the given situation is 273 N with the force applied by the foot being Fa. What is the gauge pressure inside the brake fluid?(A) 69.2 kPa; (B) 72.2 kPa; (C) 75.2 kPa; (D) 78.2 kPa; (E) 81.2 kPa. What is the torque (magnitude) produced by Fa?(A) 1.60mN; (B) 1.80mN; (C) 2.00mN; (D) 2.20mN; (E) 2.40mN. What is the value of Fa?(A) 7.53 N; (B) 8.03 N; (C) 8.53 N; (D) 9.03 N; (E) 9.53 N.
Q2/A belt drive consist of two V– belts in parallel, on grooved pulleys of the same size. The angle of the groove is 30°. The cross – section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m³ and the maximum safe stress in the material is 7 MN/m?. Answer the following questions 1- The centrifugal tension in belts is (a) increases power transmitted (b) decreases power transmitted (c) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
The height of the g point is 0.5m, the distance of the rear wheel to theg point is 1.75m, the distance of the front wheel to the g point is 1.8 m, and the car with a mass of 2100kg brakes suddenly while moving at 24v speed. l-Find the friction coefficient between the wheel and the road? 2-Find the way the vehicle takes until it stops?
Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
A tank of water sits on a cart with frictionless wheels as shown. The cart is attached to a mass and the coefficient of static friction of the mass with the ground is µ = 0.50. There is a gate blocking the tank exit and the vertical distance between the free surface and the tank exit is 2 m. The tank exit makes a 60o angle with the horizontal. The tank exit diameter is 50 mm. Now, the gate blocking the tank exit is removed. Find the mass, M, that is sufficient to hold the cart stationary.State all your assumptions clearly.
Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole assembly (HWDP, collar and drill bit) is lowered into the well. The specification of drill pipe is as follows: OD=200 mm, ID=175 mm, E = 50 GPa, G=77.2 GPa weight : drill pipe = 100,000 N , bottom hole assembly = 35,000 N Before the bottom hole assembly touch the rock formation: а) Calculate the reaction force between drill pipe and top drive drilling motor b) Calculate the elongation of drill pipe After the bottom hole assembly rest/touch on the rock formation, the elongation of the drill pipe reduces by half. c) Calculate the reaction force between drill pipe and top drive drilling motor. d) Knowing that the top steel drill pipe rotates through two complete revolutions before the drill bit starts to operate, determine the maximum shearing stress caused in the pipe by torsion.
Select a linear actuator for a pneumatic power system, capable of moving a 2700 lbf load during extend and 1800 lbf during reverse. The diameter of the stem will be 8 in. As it will withstand very strong lateral forces and must not deform. The back pressures have been estimated between 80psi and 100psi. The designer suggests an excess factor f.e. = 1.35. And determine the net forces developed, to compare against the design forces.
3. The stopper in the figure has a specific gravity of 76 kN/m°. Calculate the diameter for the valve to be keep in static equilibrium h=1.5 m. The weight of the sphere is negligible.
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
Question 4 Squared & ground end A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (16)
Q2(a). Sketch the Pneumatic Diagram and name its components.
and the staticcoeff.of coeffoF fric oniso.3thekineticcoeff of frictionis-, +