In the SPT test performed at the point where a single foundation of 1.5 m * 3.0 m will be located, the smallest value was found to be SPT-N (corrected) = 5. YASS was not observed in the field. The foundation will be built on the ground surface (Df=0 m). Calculate the safe contact pressure, in kPa, by rounding to an integer for a 20 mm seating tolerance. (Helpful information: carefully review the table that takes into account 25 mm of seating OR the relevant formulas). a. 72 b. 90 <. 61 d. 76

In the SPT test performed at the point where a single foundation of 1.5 m * 3.0 m will be located, the smallest value was found to be SPT-N (corrected) = 5. YASS was not observed in the field. The foundation will be built on the ground surface (Df=0 m). Calculate the safe contact pressure, in kPa, by rounding to an integer for a 20 mm seating tolerance. (Helpful information: carefully review the table that takes into account 25 mm of seating OR the relevant formulas). a. 72 b. 90 <. 61 d. 76

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

Distilled water at 10deg C stands in a glass tube of 9.0 mm diameter at a height of 24.00 mm. What is the true static height in mm if the surface tesnsion is 0.0742 N/m. a.24 mm b.27.4 mm c.20.6 mm d.3.4 mm
STATICS OF RIGID BODIESI NEED HELP ASAP. I need the answer after 1 hour. Please read and answer the question correctly. RATE WILL BE GIVEN ACCORDINGLY. THANK YOU EXACT ANSWER Note: The tolerance is ± 1 in the third significant digit
Show full detailed solution please.The units are in mm;1 rpm=0.104719755 rad/s
Convert 22C to Fahrenheit.
A light duty sleeve bearing operates in still air at air temperature of 70 °F and sustains a load of 350 lbs. A shaft rotates at 600 rpm. The coefficient of friction is 0.015 between shaft and bearing. The shaft diameter is 1.75 in. and the bearing length is 2.50 in. Find the probable operating temperature of the bearing. A. 143.45 deg F C. 134.54 deg. F D. 125.74 deg F B. 171.7 deg. F
6. Determine the correct statement Mark only one oval. It is preferable to have a temperature sensor or pressure sensor with non-linear response to the measured property Density is an extensive property Sum of the macroscopic energies of the pure substances is called internal energy Work transfer out of the system is taken to be negative as convention None of the given 7. Tyre pressure is 2 bar of gage pressure and it has volume of 14 litres. Determine the density inside the tyre if the tyre is in thermal equilibrium with the environment at 25
Convert 67degree celcius to rankine
Show complete solution and FBD
For the following statements, answer True or False and explain the answer briefly. The tolerance of standard mass used must be smaller than the uncertainty of analytical balance to be calibrated.
3. In the Figure below, determine: (a) the calibration range of the DP transmitter in inches of water, (b) the differential pressure head in inches water at the transmitter at 75% level Given: 100% S HLL NLL LLL Xx Y3=130 in. SG3=1.26 S = 60 in Y2 = 30 in. SG2=1.12 Y1 = 15 in. SG1 = 0.82
If an oil with density of 800 kg/m³ (instead of mercury as Torricelli did) is used to measure atmospheric pressure at sea level, what height of tube is needed? Atmospheric pressure is 101,325 Pa. Select one: O a 5.72 m Ob. 0.76 m Oc. 12.91 m Od. 10.32 m
Show the complete solution of the given problem. The answers are answers are: Cc = 24.787 Wn = 51.64 Wd = 44.72 Keq = 640 Ieq = 0.24 df = 1/2 Xo = 5mm Vo = 0