Industrial Maintenance List two things that tension members do in V-belts

Q: Which of following is not an advantage of V-belt drive over flat belt drive?      a)Efficiency of…

A: From all the statements only the first statement is not right. The efficiency of flat belt drive is…

Q: Make a circuit for representing starting system of vehicle.

A: The starting system is one of the engine's systems, which provides an engine start. To make it, the…

Q: V Belts & Circular belts with examples and with neat diagram

A: Given: Belt drive: To explain V-belt drive and Circular belt drive

Q: ME124P Practice Exercise 2 Planar Linkages: Determine the number of links, the number of 1 degree…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Davit- Pulley Pin- Cable- a

A: dp=20mm=0.78inα=15°Tmax=8kN=1798lbζp=27.5MPa=3988.538psiWL=6.7kN=1506.12lb

Q: When minimum space is an important requirement, the best type of mechanical connecting device for…

A:

Q: Describe the operating principle of the electric motor.

A:

Q: Write the difference between V Belts & Circular belt with line diagram (Any four)

A: V-Belt   1. V-Belt are in the trapezoidal cross section. 2. V-Belts are used where shaft distance is…

Q: a V-belt depends on the rotational speed of the smaller pulley.

A: In belt drive power transmission depends on following factors 1 linear velocity of velt 2 tension of…

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: Question 4 ) Listen AV-belt is wrapped around a Ø5.00-inch pulley with a 38.0° groove angle.…

A: Given data-angle in degree for belt wrap=38.0°C

Q: * The unit of measurement for torque is

A:

Q: For the pulley system below, which equation is true about the length of the cord marked as green? If…

A: To find: The length of the green cable.

Q: choose true or false : 1. The chain drive transmits more power as compared to belt drive.

A: The chain drive transmits more power as compared to belt drive. Answer: True

Q: Section angle of V-belt in belt drive φ=40˚,In order to make good contact and increase friction, the…

A: V-Belt drive is used when shaft distance is short and flat belt drives

Q: explain anchor cable with sketch

A: A heavy chain is used to hold the vessel at anchor. The chain is made of links and the length of…

Q: Chains are used in gears applications while belts are used with pulley systems. Select one: O True O…

A:

Q: The high tension side of belt is known as tight side Select one: True

A: Given: Belt pulley system

Q: Define sensors and list the various specifications that need to be carefully studied before using a…

A: Sensors basically used for the measurement of various quantities such as pressure, tempertature etc.…

Q: A single-acting actuator could be used as a component for bus opening or closing as per the…

A: Let us discuss single acting actuator.

Q: the following shadec

A: given:

Q: . When the speed of a machine is the same as that of the driving motor, the easiest method of…

A: Which is the easiest method of connecting the machine and the motor when they are at same speed.

Q: The causes of suspended load in the traction system are: a. Laminar current b. turbulent current c.…

A: The cause of suspended load in the traction system are turbulent current.

Q: A collection of rigid bodies (Links) connected together with no fixed link is called. Select one: a.…

A: Solution:

Q: A pneumatic power system will usually have a return line  a. True b. False

A: Concept: 1) Pneumatic power system consists of some pneumatic valves, Electro-pneumatic valves,…

Q: Define the following with formula and units. a) Torque b) Couple

A:

Q: write discussion about to determination of the capacity of a belt conveyor.

A:

Q: A cooling fan is connected to the driving motor by a V-belt. How many incheslong is the V-belt?

A: given:

Q: How are frictional losses measured in the drive line of a vehicle? By slowing down the dynamometer.…

A:

Q: Define Braking loads

A: Braking load/force  is the  frictional force that cats tangentially  between the brake pads and…

Q: Application of electric breking system in automobile field

A: An electric braking system is a type of braking system in which the primary operating source of the…

Q: he belts and rope drive is one of the links which is aving in Es link.

A: Which type of pair in belt drive.

Q: AC det D The balance condition for AC bridges is: Select one: O 1.7,Z,-Z,Z, O 2. R,R,=R,R3 O 3.…

A:

Q: A chain drive is no longer considered horizontal when the line passing through both shafts has an…

A: A chain drive is no longer considered horizontal when the line passing through both shafts has an…

Q: Derive the equatlon that describes the relationship between the tight and slack tenslon in V- belt…

A: The correct tension is the lowest tension at which the belt will not slide or scream when…

Q: diameter of driving pulley 200 mm diameter of drivren pulley 600) mm groove angle for sheaves 34"…

A: Given that ,  N=1440rpm D=600 mmd=200mmθ=34°m=0.5kg/mP=10KWf=0.2αs=157°Tmax=500N

Q: |5.lf the DOF is smaller than zero, all links ar mpossible to have motion. It is a ().

A: The rigid truss or frame has zero degrees of freedom and it is stable & determinate. The…

Q: Entire frame, pulleys, and contacting cable to be isolated as a single unit. B

A: TO draw the FBD of the given system we have to consider the weight and forces applied to the system.…

Q: conveyor

A: given: Explain stationary and movable trippers of belt conveyor

Q: If an actuator fails to move, name five possible causes.f an actuator has slow or erratic motion,…

A: Actuator is a component of a machine which capable in moving in a controlled mechanism.It consist of…

Q: Discuss the power trans hit by the open and crossed belts and compare between them

A:

Q: The fluid leaves the impeller with more velocity head Select one: True False

A:

Q: Q24: Briefly explain what you would change in the shown system so that less power is used to produce…

A:

Q: The energy gained due to friction in bearings is called Mechanical efficiency. Select one: True…

A: Correct answer is given below

Q: In a DCV, this part is located on either or both sides of the spool to position it in the middle…

A: DCV is the directional control value that performs 3 functions, 1. Allow the fluid flow, 2. Change…

Q: the advantages, disadvantages and applications of ball bearings

A: Application : it can handle axial and radial thrusts but can not handle very high weights Elevators,…

Q: ar is allowed to follow spira he angle rotated by link A itude of Coriolis accelerat

A:

Q: Construct a circuit drawing of a hydraulic dump lift using an open center circuit.

A: To construct an open center circuit of a hydraulic pump

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.