A W 610 x 155 beam has two cover plates 400 x 20 mm thick placed on top and bottom of thesection. The beam carries a uniformly distributed load of 73 kN/m including its own weight and aconcentrated load of 890 kN acting at the midspan of the 6 m span. If the diameter of the rivetsused is 22 mm, determine the spacing of the rivets if the allowable shearing stress of one rivet is103 MPa and an allowable bearing stress of 248 MPa.Properties of W 610 x 155A = 19700 mm²tw = 12.7 mmSy = 666 x 10³ mm³d = 611 mmIx = 1290 x 106 mm4rx = 256 mmbf = 324 mmly = 108 x 106 mm4ry = 73.9 mmtf = 19 mmSx = 44.20 x 10³ mm³w = 154.9 kg/m

Answered: Image /qna-images/answer/cf77c37e-6828-4bfc-be81-c6c4f4acd143.jpg

ion. The beam carries a uniformly distributed load of 73 kN/ centrated load of 890 kN acting at the midspan of the 6 m sp dis 22 mm, determine the spacing of the rivets if the allowab MPa and an allowable bearing stress of 248 MPa. Properties of W 610 x 155

ion. The beam carries a uniformly distributed load of 73 kN/ centrated load of 890 kN acting at the midspan of the 6 m sp dis 22 mm, determine the spacing of the rivets if the allowab MPa and an allowable bearing stress of 248 MPa. Properties of W 610 x 155

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress g and maximum compressive stress gc. 15 N 20 N/m 40 mm 40 mm F 225 mm- 40 mm 200 mm 2.5m 0.5 m
Q2: A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress g and maximum compressive stress gc. 15 N 20 N/m 40 mm 40 mm - 225 mm- 40 mm 200 mm 2.5m 0.5 m |
Q3) The beam system has a pin support at A, roller supports at D and F, and internal hinges at C. Find the deformations at C and E using the conjugate beam method. 10 kN A C D E F 100 kN-m k5 mt-5 m--5 m5 m-k10 m- = 100 x 10° mm*, and ICF Given: E = 200 GPa, IAC 50 x 10° mm“. %3D لقطة شاشة
4-43 The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be consid- ered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm². Eal = 70 GPa. A 100 mm- B 100 mm- C 800 kN/m 125 mm 11800 800 kN/m
2. Assume that a 20mmØ rivet joins the plates that are each 110mm wide. The allowable stresses are 120 MPa for bearing in the plate material and 60MPA for shearing of rivet. Determine the minimum thickness of each plate 110 mm 20-mm 0
An overhang beam is loaded as shown below. The beam cross-section was butlt by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B, -112.5 mm Web Thickness, t. -9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,-200 MPa on single shear, a, =260MPa on double shear. 1. determine the location of centroid, ȳ, from top of the beam in mm 2. determine the moment of inertia, I, of the section in mm4 3. determine the maximum allowable moment, Mall, inkn-m, base on the beam's cross section.
H.W. #4: A pin connected truss is loaded and supported as shown, determine: a) The normal stress in member DE if it has a cros ectional area of 750 mm². b) The minimum cross sectional area for member BC if the normal stress is limited to 30 MPa. -3m- 10 kN -3 m 15 kN 3m 3m
The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm, the web thickness is t-12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 3.2 KNi m 400 mm 2 KN.M BO 80 mm 12 mm 3m 1.5m
1. The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment must be determined. Replace the two forces and couple by an equivalent couple M and resultant force R at A. 2 kN 0.5 m 1.5 m 70° J0.15 m 10.15 m JA 500 N-m 1.2 kN
Compute the maximum load P (in kiloNewtons) so as not to exceed the compressive stress of 75 MPa and a tensile stress of 100 MPa for the truss members. 2.50 2.00 O 1.50 O 1.00 AA 1 60° C P 3 m 60° B
lho H.W.2: 1,200 mm The load P produces an axial strain of -1,800 pe in post (2). Determine the axial strain in rod (1). (1) rigid plate 480 mm bare 1.5 mm 600 7. 100000\ 300 mm 300 mm 600 mm (2) S. 1,0 8 11 2,09 4 1, nd supported by two rods at A and- E naliad After load Pis applie
Q4: determine the maximum tensile and compressive stresses acting normal to the beam. 50 mm 10 kN 100 mm 30 kN 6 m 2m B (2