kg/hr at 311K of a 20 wt % solution of NaOH to 50%. The saturated steam used for heating is at 399.3 K. The pressure in the vapor space of the evaporator is 13.3 kPa abs. The overall coefficient is 1420 W/. K and the area is 86.4 square meter

kg/hr at 311K of a 20 wt % solution of NaOH to 50%. The saturated steam used for heating is at 399.3 K. The pressure in the vapor space of the evaporator is 13.3 kPa abs. The overall coefficient is 1420 W/. K and the area is 86.4 square meter

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 9RQ: The evaporator design temperature may in some cases operate at a slightly ____(higher or lower)...

See similar textbooks

Related questions

Q: A four-effect evaporator is being considered for concentrating a fruit juice that has no appreciable…

A: according to the given information, we have the first stage pressure is 143.27 Kpa the temperature…

Q: An aqua ammonia absorption plant operates between pressures at 206.8 and 1378 kPaa. The strong…

A: Given data: To find: a. the mass flow of strong solution entering the generator in kg/minb. the…

Q: A four-effect evaporator is being considered for concentrating fruit juice that has no appreciable…

A: We have done solutions

Q: A surface condenser is designed to handle 12000 kg of steam per hour. The steam enters at 0.8 kPa,…

A: The answer is

Q: Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric…

Q: a light to be vaporizatio exchanger using 250 kPa steam of 90% quality. The heat losses to the…

Q: Solve the attachment

A: Given Solids sludge = 55% = 0.55 Limestone efficient = 90% = 0.9 Power plant power = 600MW Thermal…

Q: Q3 Large quantities of liquefied natural gas (LNG) are shipped by ocean tanker. At the unloading…

A: Given Data The unloading flow rate of LNG vapor is: Q=9000 m3/s The temperature of unloading flow…

Q: A rigid tank contains water vapor at 400 C and an unknown pressure. When the tank is cooled to 150…

A: Given data The water vapor temperature is T1=400°C The final water temperature is T2=150°C

Q: Boiling Points in a Triple-Effect Evaporator. A solution with a negligible boiling- point rise is…

Q: lbs -, ub = 0.044 erature of t; = 60°F and flows with an average velocity of 4 feet per s 13 ft? per…

Q: Saturated steam at 40∘C is to be cooled to saturated liquid in a condenser. The mass flow rate of…

A: (a) Write the given data. State1, T1=40 °C, saturated steamState2, T2=40 °C, saturated liquidm˙=17.3…

Q: in a surface condenser the pressure of stean is Q12 bar. The rote of cooling water flow is 40 kg/kg…

A: When the temperature of steam is equal to the boiling point at a certain pressure, it is said to be…

Q: juice of the fruit at 25 °C containing total solids 5% concentrated through evaporator, single…

Q: 5400 kg of steam is produced per hour at a pressure of 750 kN/m2 in a boiler when feed water at 41.5…

A: Water in the gaseous state is referred to as steam. This might happen owing to evaporation or…

Q: 2 m^3/min of a light oil are to be heated from 20C to 100C (with zero vaporization) in an exchanger…

Q: Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a…

A: Assuming specific heat of fruits Cf= 3.65 KJ/Kg mass flow rate of fruits= mf= 20000 Kg/h = 5.55 kg/s…

Q: Steam at a pressure of 3 MN/m, at a temperature of 250°C and flowing at a rate of 3 kg/s is…

A: givensteam 1 pressure P1=3MN/m2temperature T1=250oC=523Kflowing at rate m˙1=3kg/sthrottled to a…

Q: How do you resolve common problems with condensate traps?

A: The condensate trap is used in the air conditioning unit in which the water weight is generally used…

Q: The stream of air and gasoline vapour,in the ratio of 14:1 by mass, enters a gasoline engine at a…

A: Concept Of Steady Flow Energy Equation Used

Q: 21: Steam at a pressure of 28kpa is passed into a condenser and it leaes as condensate at…

Q: A refrigeration system using R22 is to have a refrigerating capacity of 60 kW. The evaporating…

Q: A 20% (by wt) sodium hydroxide solution is being concentrated to 50% (by weight) using an evaporator…

A: Given:- % of sodium: 20% temp of heating: 399k pressure: 13.3 kPa

Q: Bouling water at 1 atm may require a surface heat flux of 3 x 10° Btu/h · ft for a. surface…

A: Solution :- Given data :- For boiling water at 1 atm the temperature is 100Cο =3×104btu/h.ft2T…

Q: A four-stage evaporator is used to evaporate sugar juice in the sugar manufacturing plant to produce…

A: Given data: mass flow rate at the first stage, mf1= 40.32 kg/s Enthalpy at the first stage, h1 =…

Q: a. The required steam rate is = Answer kg / hour. b. Steam economy when the condensate temperature…

A: Solution : Given data : The temperature T_fat which juice enters the evaporator is 20∘C The boiling…

Q: 13608 kg/hr of NaOH solution containing 10 wt% solute. the entering feed temperature is 37.8°c. it…

Q: Design a hydrocooling unit that can cool fruits and vegetables from 30°C to 5°C at a rate of 20,000…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: An Ammonia vapor compression refrigerator has an effective swept volume of 0.308 m3 /min. The…

A: given; swept volume (vs)=0.308m3/min properties at…

Q: h of the following is not an assumption that Nusselt made in analytically deriving the average heat…

A: we are to discuss the assumptions made for convection on vertical plate

Q: Design a hydrocooling unit that can cool fruits and vegetables from 30 to 5°C at a rate of 20,000…

A: Given data, The water velocity through the channel is – Now,

Q: 3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of…

A: Solution:

Q: There are many correlations for predicting boiling heat transfer coefficient. The correlation given…

A: Solution: Given Data: Pw=1.98 barTw=125oC

Q: Effect of Feed Temperature on Evaporating an NaOH Solution. A single-effect evaporator is…

A: Given:- U= 1988 W/m2.K P=20 kPa F=9072 kg/h Ps=42 kPa Feed rate temperature, Tf=322.1k=489.9°C To…

Q: 6. Saturated steam at 1 atm is condensing on a horizontal tube at a rate of 300 kg/h. The tube is 2…

A: Given: The steam pressure, P = 1 atm The rate of steam condensation, m = 300 kg/h The length of…

Q: Water is boiled at atmospheric pressure in a square (0.2 m x 0.2 m) pan placed on top of a heating…

A: Given: A=0.2×0.2=0.4 m2σ=0.06 N/mCcr=0.15ρl=960 kg/m3ρv=0.6 kg/m3μl=0.3×10-3kg/mscpl=4200…

Q: The condenser receives 70 kg/s of wet steam at 0.05 bar and quality of 70 %. Assuming all the steam…

Q: Effect of Feed Temperature on Evaporating an NaOH Solution. A single-effect evaporator is…

Q: A single-effect evaporator is being used to concentrate 10,000 kg/h of tomato juice from 5% total…

A: Given: mf=10000 kg/h; steam pressure 143.27 kPa; initial concentration 0.05 at Tf=15 deg C final…

Q: Calculate the amount of heat required (in kJ) to raise the temperature of 23.4 g of ice at -11°C to…

A: given data m = 23.4 g = 0.0234 kg ΔHvap = 40.67 kJ/mol ΔHfus = 6.008 kJ/mol Cice = 2.092 J/g°C,…

Q: Hot air at 40 ° C and RH 65% is heated using a heat exchanger to reach 90 ° C. Using a psychrometric…

Q: PROBLEMS: 1. Steam is delivered to an engine at 5.4 MPa and 600°C. Before condensation at 31°C,…

Q: Q3: The enthalpy of vaporization for water is: H,O H,O aHvep =+ 44.0 kj/mole Calculate the AH for…

A: givenenthalpy of vaportization of water ∆Hevp=+44.0kJ/molewhenmass of water m=3gwhen mass of water…

Q: Consider a sealed can that is filled with 4.4 kg of water at 115 °C and P = 248 kPa. Now a leak…

A: Given: The mass of water, m = 4.4 kg The temperature of the water, T = 115 C The pressure of water,…

Q: later vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of…

Question

An evaporator is concentrating F kg/hr at 311K of a 20 wt % solution of NaOH to 50%. The saturated steam used for heating is at 399.3 K. The pressure in the vapor space of the evaporator is 13.3 kPa abs. The overall coefficient is 1420 W/. K and the area is 86.4 square meters. Calculate the feed rate F of the evaporator.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The evaporator design temperature may in some cases operate at a slightly ____(higher or lower) pressure and temperature on high-efficiency equipment because the evaporator is larger.
QUESTION 1 temperature of 200°C from feed water of 5°C. The steam has a dryness fraction of 0,9 when leaving the evaporator. The boiler uses coal with a calorific value of 31MJ/ka and the steam leaves the plant at a rate of 8kg per kg fuel burnt. Determine: 1.1.1 the boiler efficiency; THER MOTTADE ETA 1.1.2 the equivalent evaporation from and at 100°C;
Evaporator, single effect is used to upgrade the concentrate 8000 kg/h of tomato juice than 5% solids the total to 30% solids total. Juice enters the Evaporator at 15 °C. The Evaporator is operated with Steam (quality 80%) in 143.27 kPa. The condition of vacuum in the Evaporator allow the juice to a boil on the 75 °C. The hot kind of material dilute is 4.1 kJ/(kg °C) and the product the concentrate is a 3.1 kJ/(kg °C). Count (a) the Rate of the needs of steam = kg/h. b. The economic steam if the temperature is condensate is released at 75 °C. = (kg water evaporated/kg of steam) Help me :-(
What is the equivalent evaporation of the boiler? Determine the specific heat capacity of the delivered steam
An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of -10 °C, compute the refrigerant flow rate in kg/s assuming that the clearance volumetric efficiency applies.
Refrigerant 12 Condensing temperature = 46.2 oCEvaporating temperature = -3 oCTemperature of the suction vapor = -15.6oCRefrigerating Capacity for evaporator = 44 TONDetermine the COP
Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a rate of 20,000 kg of fruit or vegetables/h. The design must fulfill the following requirements: The unit will be an immersion flooded system. It must be able to cool down and transport the products in chill water. The tank has the following dimensions approximate. three meters wide and up to 90 cm hight. The water will circulate and be cooled through the evaporation section of a refrigeration system. The refrigerant temperature inside the coils will be -2 °C, and the water temperature must not drop below 1 °C and must not exceed 6 °C. Assuming reasonable values for the average density, specific heat, and porosity of the product (the fraction of the volume of air in a box), recommend reasonable values for: The speed of the water through the canal, the capacity of the cooling system. the compressor power.
2. Two hundred and fifty pounds of a mixture of 10 mol% propane 20% n-butane, and 70% n-pentane is completely vaporized in a pipe still in one hour. At the outlet, the temperature anc 433 F and 600 psia. What is the volumetric flow pressure are rate in cfm at the outlet conditions? Answer: The physical properties of the gas are: Tc Pc MW Propane 369.9 K 665.8 R 42.0 atm 44 Butane 425.17 K 765.31 R 37.47 atm 58 Pentane 469.8 K 845.64 R 33.3 atm 72
Differentiate between a saturated vapour and a superheated vapour?
Q3: The enthalpy of vaporization for water is: H,O H,0g sHvp =+ 44.0 kj/moie Calculate the AH for evaporating 3.00 grams of water and AH for Condensing 20 grams of water.
Liquid ammonia at 30°C is metered through an expansion valve to an evaporator operating at a saturation temperature of -5°C. Calculate the dryness fraction of the refrigerant entering the evaporator. 21.7% 0.1288% 12.88% 15.78%
100 C² saturated steam enters the turbine Vapour at 6 MPa and Sahared liquidenters the pump at apressure of 0.01 MPa If the Detemain as heat rate to borler is ISO MU D thermal off