3. Calculations and Discussion1. Calculate the theoretical output DC voltage of the half-wave rectifier circuit andcompare it with measured value. For the capacitive filter, obtain the theoretical valuesof the DC output voltage and the ripple voltage and compare these values with themeasured quantities. Determine also the practical and theoretical values of the ripplefactor.2. Calculate the theoretical output DC voltage of the center-tapped full-wave rectifiercircuit and compare it with measured value. For the capacitive filter, obtain thetheoretical values of the DC output voltage and the ripple voltage and compare thesevalues with the measured quantities. Determine also the practical and theoreticalvalues of the ripple factor.3. Repeat the calculations for the full-wave bridge rectifier and filter circuit.4. Determine the peak inverse voltage (PIV) on each diode in the three rectifier circuits.5. If diode D4 in the bridge rectifier circuit of Figure 5 was removed or burned, explainthe operation of the circuit in this case and sketch the predicted waveform of theoutput.6. Explain the effect of increasing the filter capacitance on the output voltage in the half-wave rectifier and filter circuit.7. Compare the DC output voltages of the three rectifier circuits. Which circuit has thehighest output? On the other hand, which circuit has the lowest peak inverse voltageon each diode?8. What value of filter capacitor is required to produce 1% ripple factor for a full-waverectifier having a load resistance of 1.5kQ? Assume that the peak value of the outputvoltage is 18V.

Answered: Image /qna-images/answer/091f1099-4f06-40f2-814a-53a2c9020d45.jpg

late the theoretical output DC voltage of the half-wave rectifier circuit an are it with measured value. For the capacitive filter, obtain the theoretical value e DC output voltage and the ripple voltage and compare these values with th ured quantities. Determine also the practical and theoretical values of the rippi

late the theoretical output DC voltage of the half-wave rectifier circuit an are it with measured value. For the capacitive filter, obtain the theoretical value e DC output voltage and the ripple voltage and compare these values with th ured quantities. Determine also the practical and theoretical values of the rippi

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

For the circuit below, XL=60 R1=40 Is R2=90 El=100V20° Ad R3=80 V3 Xc=707 ZT a. Calculate the total impedance (Z). b. Compute the source current (Is). c. Find the current across the capacitor Xc. d. Calculate the voltage across the resistor R3.
esistance 2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KQ. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = Vdiode = DIODE VLOAD: VLOAD Peak = .. Load VLOAD VLOAD DC= Supply 203 exxxx Vi wwwww
3.3 Procedure: 1. Connect the circuit shown in the figure (6). Choose RL to be 100ohm. CT R D2 Figure (6) 2. Set the function generator by an AC voltage (220 (r.m.s)V/ 50 Hz) and draw the input waveform. 3. Connect the Oscilloscope to both ends of the resistance, Draw the wave shown in the screen of the Oscilloscope. llle
d. Draw the phasor diagram of the voltage and current (with magnitude and direction).e. Is the current leading, lagging, or in phase with the voltage? If leading or lagging, by how much (write your answer in degrees).f. If these are the voltage and current waveforms of a specific circuit branch, what is the impedance of that branch? (Hint: Use Ohm's Law)
Learning Goal: To see how an R-C circuit with an AC voltage source can be used as a high-pass filter. A 10.0-0 resistor and a 100-pF capacitor are connected in series with an AC voltage source with frequency 1000 Hz and maximum voltage 100 V. Part A - Complex impedance Find the complex impedance for this circuit, in 0. Format: Since Z = R+ Xị, your answer consists of two values: the resistive part Rand the reactance X. Enter them separated by a comma: R, X > View Available Hint(s) ? Your submission doesn't have the correct number of answers. Answers should be separated with a comma. No credit lost. Try again. Previous Answers Submit Part B - Complex impedance in polar form If the impedance Z is written in polar form (Zel), what are Z (in a) and o (in degrees)? Format: Enter them separated by a comma: Z. o • View Available Hint(s) ? Submit
6.- .Detarmine the time constant of the circuit. b) Sketch the wave for ms for ve and ic. 30uf 10k
II. A. FACT OR BLUFF Directions: Write TRUE if the statement is correct and FALSE if the statement is wrong. TRUE 1Both ACa6 n dthe flow of current in a circuit. dically. 4. AC can be represented by waves. 5. Triangie waves are often used in digital and switching electronics to test their operation. 6. The most common waveform in AC is square wave. 7. The frequency of direct current ranges from 50 Hz to 60 Hz.
Q3\ Draw the bridge full wave rectifier and explain the operation of each part in the circuit.
SERIES CIRCUIT 1. Create the circuit shown in figure A. 2. Measure and record Vad, Vab, Vbc, Vcd, Vac, la, Ib, lc and Id. 3. Compute for the total resistance. 4. Using the formula Rt = Vad/la, determine the totalresistance on the circuit 5. Record the result in table 1. PARALLEL CIRCUIT 1. Create the circuit shown in figure B. 2. Measure and record Vah, Vbg, Vcf, Vde, 16k, 13k and 12k and Itotal. 3. Compute the total resistance. 4. Using the formula Rt=Vah/It, compute for the totalresistance. 5. Record the results in table 2. R3 a b. 6k2 V1 R2 S3ka Figure A 12V R1 2kQ a d V2 R6 R5 R4 12V 23kn 2k2 Figure B g e Table 1 Vab Vbc Vcd Vad Vac la Ib Ic Id Measured Values Computed Values Table 2 Vah Vbg Vcf Vde It 16k 13k 12k Rah Measured Values Computed Values
Q2- For three-phase bridge inverter with resistive star-connected load: 1- Draw the circuit. 2- For 120 conduction angle, draw the waveforms of vab, ia, in and ie .
1. Write your understanding on resonance condition for an RLC circuit. What are the reactance's for a capacitor and an inductor in RLC circuit?
Q5: Analyze the single phase bridge inverter whose output voltage is a semi- square of 60% On-time at 50 Hz. The inverter is connected to 100V de source and its load is composed of 100 in series with 100mH inductance. 1. Sketch to scale load current waveform at steady-state (derive an expression for the peaks of the current in term of system parameters) and find its RMS value. 2. Sketch input current and output voltage waveforms. 3. The RMS value of output voltage and its components up to fifth harmonics. 4. Output steady-state power, power factor and power associated with each harmonics components up to fifth harmonics. 5. Find THD of the output signal. [Hint: V₁ =4E/(√na) sin nß/2] ← 48 Stitch It!