List (1) 1. grinding process: 2. spot welding: 3. drawing: 4. runner: 5. wavy edges: 6. hot forming: List (II) a) a cross section of bar is reduced by pulling force. b) get bad dimensional accuracy of products. c) a process that involves the use of heat and pressure. d) strip's edges elongate more than the center. e) channel carry molten metal from spure to mold cavity. f) it has wheel consists of a large number of abrasive particles called grains.

List (1) 1. grinding process: 2. spot welding: 3. drawing: 4. runner: 5. wavy edges: 6. hot forming: List (II) a) a cross section of bar is reduced by pulling force. b) get bad dimensional accuracy of products. c) a process that involves the use of heat and pressure. d) strip's edges elongate more than the center. e) channel carry molten metal from spure to mold cavity. f) it has wheel consists of a large number of abrasive particles called grains.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
Please answer number 6 only (Complete solution, with diagram/illustrate or analysis/explanation etc.) That would be soooo helpful and appreciated, thank you in advance!! *the previous answer is cropped, i cant see the full solution.
Q.4- Write (True) or (False) and correct the wrong sentences for the following: 1. Chills are used to increase the heating rate of metal. 2. Motion of job is forward rotary in broaching operation. 3. The upset type of forging makes increment in the diameter of the workpiece. (1-2) Option 1 4. The torch size of (GTAW) process is larger than other (PAW) process. 5. Only two perpendicular components of cutting force act on the tool in case of oblique cutting. 6. The semicentrifugal casting, is used for casting articles of symmetrical shape about vertical axis. 7. In planer machine tool, workpiece remains stationary and tool reciprocates. 8. Boring is performed on the inside diameter of an existing hole. 9. In grinding processes, small grit sizes used to grind soft materials and permit larger material removal rates. 10. Side rake angle on tools is provided to control chip flow.
23- Complete the sentence with the appropriate terminology. In .. a simple punch and die that each have the included angle are used to bend the part. wrinkling b) tearing edge bending V-bending e) earing
24) are 3 methods that can be used to control the metal flow under the blank holder in deep drawing process. 25) are 4 reasons why do Deep Drawing of Cup Shaped Shells Fail. 26) which means the reduction in diameter of the starting end of the wire in wire drawing process.
Introduction for shaper work process please elaborate in 200 words
25- Which one of the following operation is not a sheet-metal forming process? Seaming b) Deep drawing C) Spinning Heading e) Hemming
To make 5 cast iron tool holder as shown in Figure 2 on a one time order, and the inside hole surfaces should be smooth, what manufacturing processes would you suggest for the part. a)die casting, which can make the part in high production rate with smooth surface and precise dimension b)Machining processes from the 2X1.5 inch iron bar stocks with no initial tooling cost. cut the bar into 6 inch long pieces with bandsaws mill all the flat surfaces on a milling machine drill the two holes on the same milling machine or a drill press c) sand casting, which has much lower initial tooling cost than die casting and reasonable production rate. drill to make the smooth inside surfaces of the two holes on a milling machine or drill press. d) forging process with rounded edges and corners. drill the two holes on a milling machine or drill press.
Need answers to be rounded to 3 sig figs. Thank you!
Hi, our topic here is about METHOD OF SECTIONS kindly help me find the correct solution to this problem. Asap! Thank you!
Consider the red aluminum tool holder shown in Figure 4. Your job shop has been contracted to make 5 pieces this year, with possibility of making 5 more each year in the future. Consider the process options below, which option is the best? a) using sand mold, cast the holder without hole using a mill, cut all planar surfaces (smooth surfaces) using a mill or drill press, cut the hole anodizing the holder to red color b) using injection molding anodizing the holder to red color c) using die casting, cast the holder anodizing the holder to red color d) using a hacksaw, cut a piece of 3"X3" bar stock to length using a mill, cut all planar surfaces using a mill or drill press, cut the hole anodizing the holder to red color
Q.1- Answer two of the following: a) What are deference between hot forming and cold forming in metal forming processes? b) State the main types of die casting machines and Compare (in table) between them. c) Compare (in table) between water jet cutting (WJC) Abrasive jet machining (AJM).