3. The table below has a variety of feature control frames that create different datum reference frames. Next to each feature control frame, identify the degrees of freedom (x,y,z,u,v,w) constrained by each referenced datum feature. Remember, a lower precedence datum feature can not constrain any degrees of freedom that a higher 7 precedence datum feature has already constrained. See the isometric view to the right for the labeled degrees of freedom. n +.005 2X D.250 -.002 ø.005 B -.600 ±.004 .300±.002 C. 0.682±.002 E. Constrained Degrees of Freedom (x,y,z,u,v,w) This datum Primary Secondary Tertiary reference frame O ø.005 AGD Ø.005 EFB Ø.005 FEB 3. ø.005 C- EDA +ø.005 AH 6.34

3. The table below has a variety of feature control frames that create different datum reference frames. Next to each feature control frame, identify the degrees of freedom (x,y,z,u,v,w) constrained by each referenced datum feature. Remember, a lower precedence datum feature can not constrain any degrees of freedom that a higher 7 precedence datum feature has already constrained. See the isometric view to the right for the labeled degrees of freedom. n +.005 2X D.250 -.002 ø.005 B -.600 ±.004 .300±.002 C. 0.682±.002 E. Constrained Degrees of Freedom (x,y,z,u,v,w) This datum Primary Secondary Tertiary reference frame O ø.005 AGD Ø.005 EFB Ø.005 FEB 3. ø.005 C- EDA +ø.005 AH 6.34

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Scaling with an arbitrary point is a best example of ---- * O jodeling jransformation visual transformation O jcombined transformation O non of the above
USE MATLAB (Convolutional Code) The vector representation of a convolutional code is g1=[1 1]and g2=[1 0]. If the received sequence is 11 11 01 10, please use Viterbi Algorithm todecode it. Please show the full trellis diagram, including the updated trellis statemetrics.
The Vehicle stands at point [2,1]' and theta angle 45degree on World frame. The sensor mounted at [1,0] point on Vehicle. The sensor has detected an obstacle at point [2,-1] on Sensor frame. Firstly calculate from the sensor frame to the Word frame Homegenous transformation Matrix step by step. Find the obstacle position on World frame? y4 W
5. When two frames have the same orientation, then the (W,P,R) values of their corresponding frame transformations are (a) zero (b) non-zero 6. The robot programmer sets up UT[1] for a sharp-tip pointer that is held by the robot gripper. If UT[1] is accurate, it means that (a) UT[1] is activated in the robot system (b) The origin of UT[1] frame in the robot system is exactly at the tip of the actual pointer (c) The origin of UT[1] is aligned with the origin of Def-TCP frame
Problem 04 Datal 3 7 5 7 3 Data 2 -7 4 7 -9 7 8 4 3 Data 3 Store the data in a 3x8 array (use variable name data), where each row is storing the corresponding set of row data ('Datal', 'Data2', or 'Data3'). Show how to do the following analysis by hand calculation and using MATLAB commands (write down the command and the result). 4 -9 1 1 5 6 a. Mean of each row of data: b. Mean of each column of data: c. The median of each row of data: d. The standard deviation of each row of data: e. The variance of each row of data:
Hello I'm having trouble with this assignment, I don't understand how the plot function works for ordered pairs. I undertand that the points of the line would be the origin(0,0) and (x = cos(theta) . y = sin(theta)).
21. The programmer uses three-point method for UT[2] setup for a sharp-tip pointer. If the programmer recorded each of three-points by precisely contacting the sharp-tip to the tip of the stationary reference pointer on the table, then (a) UT[2] setup is accurate (b) UT[2] setup is not accurate (c) the accuracy of UT[2] setup is still uncertain 22. User frame UF[3] is accurately set up on the part reference surface which is unparallel to the surface where the robot is mounted. To jog the robot TCP to move perpendicularly to the part reference surface, the programmer (a) needs to select World jogging coordinate system (b) needs to activate UF[3] and select User Frame jogging coordinate system
Q3) For the Fig. Q3 shown below: 1- Assign the coordinate frames base on D-H representation. 2- Fill out the parameters table. 3- Write all the T matrices. 4- Write 9T in terms of T matrices. d2 Fig.Q3 Given: The general form of the Forward Kinematics (Link Transformation matrix): 0. -s6; s0;ca;-1 c0,ca;-1 -sa;-1 -SC;-1di. ca;-1 ce; ai-1 i-lT = s0; sa;–1 c0;sa;–1 ca-1 ca;-1d;
Given: Mass = M, Radius = R, Moment of Inertia = I, Distance = H, Gravity = g, Initial timing = 0 Unknown = How long will the [delta t] process take? (time) Please keep in mind that almost every variable is unknown! We are given no numbers and are instructed to generate a solution using the variables [ "R, M, g, I and H." ] Target = Find an equation that, if we could substitute numbers, would determine how long the process would take. Newton's second law and torque seem to be relevant based on how the problem is written. * Also please show drawing based on what we are calculating
3-D Model the following angle tab part. Unit system: MMGS (millimeter, gram, second) Part origin: as specified (center of hole) Material: 6061 Alloy 170 R O a. 1280.91 grams O b. 1593.72 grams O c. 1147.25 grams O d. 1398.47 grams 3 8x 45 80 960- R20 Origin What is the overall mass of the part? 116 156 13 040 8x as -2x @ 15
Help with the MATLAB code to do the following: Given an audio recording of vehicles, compute Power Spectral Density, 1/3 octave band level, octave band level, A-weighted Leq, C-weighted Leq, L10 (unweighted since sample is short), L90 (unweighted since sample is short). If the measurement is made at approximately 50 ft, and that the vehicles are moving at an average of 65 mph, what is the flow rate Q? If instead, the noise is dominated by 1-2 motorcycles, how fast are they going? Given- -The data are in counts -Calibration factor is 133 uPa/count -Sample rate is 44100Hz. -Remember that in air the dB reference is 20 uPa -Pwelch requires that the inputs are doubles
Figure 1 shows a six degree of freedom industrial robot. i. Construct the coordinates frames based on the D-H representations. ii. Complete the D-H parameter as illustrated in Table 1.