Member ACD is supported by cable BC and a support at A as shown. The support at A only 1. allows free rotation about y-axis and prevents all other displacements and rotations. The cylinder at D has a weight of 400 N. At E it is subjected to a force F = {50i + 50j – 200k} N. Determine the components of reaction at A and the tension in cable BC needed for equilibrium. 0.5 m 1 m D 3 m E C F

Member ACD is supported by cable BC and a support at A as shown. The support at A only 1. allows free rotation about y-axis and prevents all other displacements and rotations. The cylinder at D has a weight of 400 N. At E it is subjected to a force F = {50i + 50j – 200k} N. Determine the components of reaction at A and the tension in cable BC needed for equilibrium. 0.5 m 1 m D 3 m E C F

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.90P: The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of...

See similar textbooks

Similar questions

The 14-kN weight is suspended from a small pulley that is free to roll on the cable. The length of the cable ABC is 20 m. Determine the horizontal force P that would hold the pulley in equilibrium in the position x=5m.
The vertical pole is acted upon by an 8.4kN force. The pole is supported by a ball and socket at A and two cables, BD and BE. Determine the reaction forces at A and the tension in each cable. Show the FBD and use 3D Equations of Equilibrium in Section 5.3. 10 m 8.44% 7m 6m C B E fr 6m-
Problem 2. Consider the frame loaded as shown. If the reaction force at the roller at F is 250N, then find the force P applied for equilibrium. 0.2 m 0.2 m 0.3 m E 60° |A |B 0.6 m 0.3 m
Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are properly aligned on the shaft. Determine the magnitude of the vertical force P that must be applied to the handle to maintain the equilibrium of the 100kg bucket. Also, calculate the reactions at the bearings. Since the bearings at A and B are aligned correctly, only force reactions occur at these supports. 0.3 m 981 N 0.5 m 0.1 m By 0.4 m B 30% 0.3 cos 30°m X 0.3 m G 0.5 m 0.1 m 0.1 m X 100 kg 0.3 m 30% 0.3 m
Determine the magnitude of the reaction at support A, in lb. If: P = 330 lb, h = 19 in., A = 22 in. b = 8 in.
The beam is supported at A by a pin support and is held in equilibrium by the cable at B. Choose two correct answers from the following. 500 N The horizontal component of the reaction at support A is 200 N O The vertical component of the reaction at support Ais 400 N O The tension in the cable is 600 N O The magnitude of the reaction at support A is 447.21 N O The tenslon in the cable is 500 N 5.
27- O A) -2/7 B) -3/7 C) -4/7 D) -5/7 O E) -6/7
Determine the reactions at A and E if P = 310 N. What is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads.
The 10-kg pipe is supported at A by a system of five cords. Determine the force in the cable AB for equilibrium: B 60° Select one: O a. T(AB) = 226.56 N O b. T(AB) = 113.28 N O c. T(AB) = 593.83 N O d. None of these Activate W 0of the blosk, shown in the following figure, so that the tension developed in any
Determine the reactions at A and E if P= 470 N. What is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads. pls show the step by step solution
The boom AB is held in equilibrium by a ball-and-socket joint A and a pulley and cord system as shown. Determine the x, y, z components of reaction at A if F={−2200k}lb Determine the tension in cable DEC.
Cable AB passes over the small ideal pulley C with- out a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension T in cable CD? 4 A 45° 2' B 50 lb 17/17