mm50 mm 30 mm в с IB 10° k (a) (b) Prob. 5-24

Q: 4. A foot valve for a pneumatic system is hinged at B. Knowing that alpha = 30 degrees, determine…

A:

Q: Determine the moment at B in kiloNewton-meters (kN-m)

A: Given data : uniformly distributed load =19.2 kn/mSupport :1: Pinned support2: Roller support

Q: The 3.1-lb collar is released from rest at A and slides freely down the inclined rod. If the spring…

A: The given collar structure is analyzed by using the equation of the equilibrium forces. The…

Q: Q The two-steel shaft shown in figure have the same diameter and weight 170 Ih cach. Neglect the…

A: Let the normal reaction at point C = NcThe reaction of the wall at D = N2And the reaction by wall at…

Q: 1. A 250mm x 300mm beam has a simple span of 12 meters. It is necessary to place a support at…

A: Deflection: The displacement of any structural element in the structure which is displaced under the…

Q: 4. A foot valve for a pneumatic system is hinged at B. Knowing that alpha = 30 degrees, determine…

A:

Q: Determine the vertical and horizontal components of reaction at the pin support A and the angular…

A: Given data: mass of rod = 12 kg angular velocity of w= 5 rad/s

Q: Now find M (the magnitude of the couple in the original system) so that the moments about point B…

A:

Q: The spool of wire having a weight of 300 lb rests on the ground at B and against the wall at A.…

A: Draw the free body diagram.

Q: Problem 4. A. Draw the F.B.D. of the frame shown in Fig. B. Draw the F.B.D. of the figure shown in…

A: In the Given questions two different figures are shown we have to determine the FBD of the figures

Q: What is the value of the moment at B, in N-m? P(N)=450

A: Given, P= 450 N let vertical  reactions at A and C be VA and VC respectively (↑)

Q: Situation 10. A single force P acts at C in a direction perpendicular to the handle BC of the crank…

A: Data given: MX = 20 N-m MY = -8.75 N-m MZ = -30 N-m Asked: Magnitude of P and the value of θ and ϕ

Q: The motion of pin P is guided by slots cut in rods AD and BE. Knowing that bar AD has a constant…

A:

Q: 1.) The cylindrical drum is filled with water with unit weight of water 9800 N/m3. The cylinder is…

A:

Q: Derive the stiffness matrix for the nonprismatic bar shown in Figure P3-53 using the principle of…

A:

Q: 1.) The cylindrical drum is filled with water with unit weight of water 9800 N/m3. The cylinder is…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Problem 4. A. Draw the F.B.D. of the frame shown in Fig. (4-A). B.Draw the F.B.D. of the figure…

A:

Q: Determine the moment MOA produced by the force F which tends to rotate the rod about the OA axis.…

A: Determine the moment MOA produced by the force F which tends to rotate the rod about the OA axis.

Q: Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L = 6.5…

A:

Q: From the influence line of moment at D, what is the value of moment Mp when x = 13 m due to a unit…

A:

Q: The weight of the cylindrical tank is negligible in comparison to the weight of water it contains…

A: To find out the, 10) Find the smallest force Q required to tip the tank. 11) Find the smallest μs…

Q: 24 in. 75 mm 30" B. 200 mm Fig. P6.F5 100 N 50 N Fig. P6.F6 9 in.- 6.F7 A small barrel weighing 60…

A: (6.F6) Draw the free body diagram.

Q: alculate the moment at point (G) of the forces shown in ngure. S N.m 50 2N 3N

A:

Q: Find the ratio of the revolutions per minute for the fan pulley to the revolutionsper minute for the…

A: Given: The diameter of the fan pulley is 3 in. The diameter of the motor pulley is 2 ¼ in or 2.25…

Q: The bar rotates in the horizontal plane about a smooth pin at the origin. The 2-kg sleeve A slides…

A: Given ;

Q: The 2 kg block is released from rest at A and slides down along the smooth cylindrical surface. If…

A:

Q: QI/Answer either A or B. F-500 N A/ Determine the resultant moment produced by the forces about…

A:

Q: Detemine the vertical reaction at C in kN. Express your answer in 2 decimal places. Neglect sign. w…

A:

Q: 3. A lever AB of negligible weight is hinged at C and is attached to a control cable at A as shown…

A: Considering FBD of lever ABAE= 20 Cos 20°=  18.79 cmCE= 20 sin 20°= 6.84 cmDE=CD-CE∴ DE=…

Q: The 2kg collar is released from rest at A and slides down the inclined fixed rod in the vertical…

A:

Q: Given the rod below (E = 70Gpa; a = 23 × 10-6 1/°C; diameter d = 50mm; AC = 400mm; BC = 800mm, P =…

A:

Q: 2. A beam is supported by a fixed support at and a roller at B. A uniformly varying load is acting…

A: The FBD:

Q: I. For the frame shown (AN 15) , the force F acting upward at C causes a horizontal reaction of 100…

A: The body in equilibrium fulfills conditions which are as follows Sum of all the forces along x…

Q: When θ = 30°, the 25-kg uniform block compresses the two horizontal springs 100 mm. Determine the…

A: Draw FBD:

Q: etermine the magnitude of the moment of P about the following lines in N. m

A: Given figure shows the parallelepiped, it is required to find the magnitude of moment of force "P"…

Q: 4. The'rectangular gate AB is 3.05 m x 1.22 m in dimension and its pin connected at the point B. If…

A: FBD of the given problem:

Q: The magnitude of the force P is 405 N. Determine the magnitude of the moment (Nm) of P about the…

A: Consider the free body diagram;

Q: ) The 2 kg BC ring can only move left and right on the frictionless rigid arm. Ring BC is connected…

A:

Q: Derive the stiffness matrix for the nonprismatic bar shown in Figure P3-53 using the principle of…

A:

Q: During a hammer thrower's practice swings, the 7.1-kg head A of the hammer revolves at a constant…

A:

Q: 1. A 200mm x 300mm beam has a simple span of 8 meters. It is necessary to place a support at midspan…

A:

Q: Consider the given figure. a. Determine the value of Wo. b. Determine the value of the maximum…

A:

Q: Problem 3-Determine the moment applied at point F to achieve equilibrium of the system. Use the…

A:

Q: RTER- LE s(1.02)

A: Fh   = rho x g x A x h' Horizontal force acting on the body is equal to the force on projected Area…

Q: Find the magnitude (in Nm) of the couple moment acting on the pipe assembly  if P = 56 kN. Round off…

A:

Q: Determine the tension developed in wire CD required for equilibrium of the 30 lb cylinder E and the…

A: Given that :

Q: A motor transmitting 60 kW at 600 rpm drives a solid steel shaft ABC with a diameter of 50 mm. The…

A:

Electric Current, Voltage and Electric Power

The term electric current is the flow of electrons or electric charges. The drift of electrons is proportional to the amount of voltage or potential difference applied. The more is the voltage, the more will be the electron drift. The amount of electric current a circuit possesses is proportional to the density of electrons or electric charge.