O A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the output voltage and current through each SCR, for thyristor firing angle a = (45°& 75°) (b) Determine the average value of the output voltage and current if the line voltage is Vms = 400 V and R= 100 ohms when a 30°, a = 90°, and a = 135°. (c) How is the average load voltage affected if thyristor T2 failed to open circuit? %3D %3D %3D %3D

O A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the output voltage and current through each SCR, for thyristor firing angle a = (45°& 75°) (b) Determine the average value of the output voltage and current if the line voltage is Vms = 400 V and R= 100 ohms when a 30°, a = 90°, and a = 135°. (c) How is the average load voltage affected if thyristor T2 failed to open circuit? %3D %3D %3D %3D

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + Vs D3 Y D2 9V sin(2n 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RĻ. Peak voltage: Waveform period: Frequency 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of vs for simplicity).
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Note: Answer All question 1: A) For a single-phase half-wave uncontrolled rectifier with (RL) load, find the rms value of the output voltage (V) and form factor (FF%) with supply voltage: v,(t) = 10 sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms. The conduction angle B = 220°. %3D
a) Name of the Circuit? (Assume Silicon Diodes) , 4:1 D b) Find the peak input voltage to the 120 V rms diodes. R 1.0 k D2 c) Find the average output voltage? d) Find the DC current? d) Find the Peak Inverse Voltage of the diodes? e) Draw the output waveform. eetee
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Design a full wave rectifier based on the circuit shown in Figure 5 below: N1: N2 D3 D1 RL vs D2 DA Figure 5 The required specification for the full wave rectifier circuit includes the peak output voltage of 5 V, deliver 100 mA to the load R1, and produce an output with a ripple of not more than 5 percent. An input line voltage of 220 V (rms), 50 Hz is available. Given Vy = 0.7 V. (d) Calculate v, (max). (e) Find the required turn ratio for the transformer. (f) Determine the Peak Inverse Voltage (PIV). What is the effective load resistance? (h) Determine the required capacitance of the filter capacitor.
(a): Determine the ripple factor for the filtered bridge rectifier with a load as indicated in the following circuit diagram: (b): Sketch the voltage across R. in two cases ( when C is connected and when C is removed). Note that all diodes are of Silicon. 3:1 Dy D 390 Vpp Outpar 60 Hz R 380 Ohm D 1900F
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V