A trapezoidal channel has a side slope of 2, a bottom width of b meters and a depth of flowof y meters.What is the wetted perimeter of the channel?O a.O b.by +O d.260.5y + 26⁰.5Ọ C. b +2yb25by +2y60.5

Side slope=2 Bottom width = b m Depth of flow= y m

Answered: of y meters. What is the wetted…

of y meters. What is the wetted perimeter of the channel? O a. by + O b. 0 с. O d. -26⁰.5 y + 260.5 b + 2yb0.5 by + Zybas

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 3.5 m D 7m B 2.5m *

Q: A long slope is formed of a cohesionless soil, as shown below, making an angle of 25 wih horizontal.…

A: A long slope- Angle with horizontal β=25o, Angle of internal friction ϕ=30o, Dry unit weight-γdry=16…

Q: A-2.40% grade meets a +1.50% grade at station 44+25 and elevation 3386.96 ft, 400-ft curve, stakeout…

A: The initial grade of the curve = -2.4% The final grade of the curve = +1.5% The station of point of…

Q: Draw Shear and Bending moment diagrams for the frame shown below using Force Method and Virtual work…

A: Since you have asked multiple methods we will solve the first method for you. If you want any…

Q: Q1/ Water flows steadily from a nozzle into a large tank as shown in the Fig. the water then flows…

Q: 2. A symmetrical parabolic curve has an ascending grade of 3.2% and a descending grade of 2.8%. If…

Q: 3) The rainfall gauging station measurements of an 8-hour storm is given below. The initial and…

Q: The Grain size analyses results are given in Figure 1 for Soils A and B. Answer the following…

A: The grain size analysis for soils A and B are given:- The liquid limit of soil A = 65% The plastic…

Q: only HANDWRITTEN answer needed ( NOT TYPED)

A: The loading diagram is shown below.

Q: Define the elemental stiffness matrix for element 2-3 in the given truss structure 1 45 90 45 2 3

Q: 1. Determine the midspan deflection of the beam loaded as shown using area moment diagram by parts…

A: To determine:deflection at the centre of the beam

Q: It is proposed to use a two-stage plant instead of the single stage plant. The total volume of filte…

A: The total volume of filter medium = 0.082 ha-m The flow rate = 3.79 mld The influent BOD = 240 mg/l…

Q: Q.3 Find the discharge in each pipe for below problems. Solve each questions up to three trials. hf…

Q: A line measures on the ground 161.287m. Using a ruler, the length of this line is 15.97cm on the…

Q: Q6 What force does water exert on the base of a house tank of base area 1.5m² when it is filled with…

A: Base area A = 1.5 m2 Height h = 1 m, Density of water ρ=1000 kg/m3,g=10 m/s2 To Find- The force…

Q: A prismatic bar has a cross-section of 25 mm by 50 mm and a length of 2000 mm. Under an axial load…

A: →Cross section Area of prismatic bar A= Breadth×Depth=25×50mm→Length L=2000mm→Axial load…

Q: Plot the shear and moment diagrams for the beam loaded with both the distributed and point loads.…

Q: Determine the product of inertia (lxy) for the composite

A: ###Product of Inertia Ixy about centroid axis x,y #####

Q: A long slope is formed of a cohesionless soil, as shown below, making an angle of 25 wih horizontal.…

Q: 2- Draw the shear force and bending moment diagram for the beam as shown below 10 kN/m ↓▬▬▬▬ 15 m-…

Q: A complete-mixed activated sludge process (CMAS) is to be designed to treat 6.0 MGD of primary…

A: To determine the minimum MCRT, we can use the following equation: MCRTmin = 1 / kd MCRTmin = 1 /…

Q: R20

Q: Q.3) Considering the given test setup answer the following questions. a) Calculate the coefficient…

Q: Calculate Reynold's number if a fluid ha 00 kg/m³ flows through a pipe of radiu

Q: A crop is to be grown, for the month of December. If the effective rainfall in that month is 1.7 cm,…

Q: Create a two-dimensional contour plot of the bending and transverse shear stresses over the length…

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

Q: Q2/ A well of diameter 30 cm fully penetrates a confined aquifer of thickness 1.5 m. When pumped at…

Q: A line RS has a length of 7.57cm on a map having a scale 1/500, what is the length of RS on the…

A: Length of RS line on map (l) = 7.57 cm Scale (S) = 1/500 Determine the length of RS on the ground…

Q: ation tion Military, mining, land development, resource management, hydrography; all these domains…

A: This question is related to the Surveying Engineering from Civil Engineering. In this question ask…

Q: A steel wire (E= 200 GPa) of diameter d= 1.25 mm is bent around a pulley of radius Ro= 500 mm. What…

Q: Assignment ( Determine the reactions at the supp- 5 kN/m Hinge -20 m -20 m+ Ax A 5 kN/m B C -50 m

Q: A strata of 3.5 m thick fine sand has a void ratio of 0.7 and G of 2.7. For a quick sand condition…

Q: Calculate Reynold's number if a fluid having a viscosity of 0.25 N.s/m² and density of 800 kg/m³…

A: Viscosity=0.25 N.s/m2 Density =800 kg/m3 Pipe radius=10 mm, diameter D=20 mm. Velocity V=2 m/s…

Q: Problems for Practice 7. A fluid flows at 0.002 m³/s through a diameter pipe. Determine whether the…

Q: Determine the diameter of the penstock, Runner and type of turbine Ø= 0.70 Given Data Head provided…

A: Head provided is 115, Power produced = 135 MW, Number of turbines = 5, Runner and type of turbine…

Q: The highest velocity (in cm/sec) for flow of water of viscosity 0.01 poise to be laminar in a 6 mm…

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

Q: 3) Compute the deflection at 4m from the left support.C 300N/m A k 3m 7.5m- 7 4 I= 15-5x10mm E = 100…

Q: 3 A water supply board is responsible for treating 1500 m³/day of water. A settling column analysis…

A: A water supply board- Discharge for treatment Q= 1500 m3/day, Surface overflow rate SOFR= 20m/day.…

Q: For the truss shown in the figure, determine (Approximately) the bar forces assuming that the…

Q: - DESIGN THE T-BEAM AND SHOW THAT TENSION STEEL YIELDS AND THE BEAM IS TENSION CONTROLLED

A: Consider that given load is factored uniform load 'Wu = 50 KN/m' Factored Maximum moment on beam is…

Q: A steel rod of 2 cm diameter and 5 m long is subjected to an axial pull of 3000 kg. if E = 2.1 x 106…

A: Diameter d=2 cm Length L=5 m Axial pull P=3000 kg Elongation of rod=?

Q: From the given trusses deformice all the forces carried by each member of the trusses shown: 4.kn

A: Determine the force in each member of the truss. Let's solve using Method of Joints

Q: Requirements: instructions your final box answer my id last decimals places 789 solve part (b) ASAP…

Q: 3 Determine the vertical displacement of Joint A by the Method Virtual Wok if member AE is…

A: The virtual work method is mainly related to a force that is acting on a particle or member of the…

Q: A contractor has compacted the base course for a new road and found that the mean value of the test…

Q: Using the indices proved below compute the estimate of a house having 65,000 m2 of floor area, the…

A: Delhi cost index = 1.20 Agra cost index = 1.14

Q: 1000 Ib

Q: If the total area of the comfort room is 36.75m2. What should be the number of exhaust fans, and how…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

100%

A trapezoidal channel has a side slope of 2, a bottom width of b meters and a depth of flow
of y meters.
What is the wetted perimeter of the channel?
O a.
O b.
by +
O d.
260.5
y + 26⁰.5
Ọ C. b +2yb25
by +
2y60.5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows in a triangular channel at a velocity of 2.9ft/s. Find the depth of flow (in ft) if the channel slope is 0.0015. n=0.014 CHOICES: 2.57 7.52 5.72 5.27
Water flows at 25 m^3/s down a rectangular channel made of unfinished concrete. The channel has a width of 4 m and a downward slope of 0.008, and the water depth is 2.6 m at the control section A. Calculate critical depth, normal depth and identify the channel surface profile. Determine the distance X from A to where the depth is 2.7 m (Control Section B). Use increments of Ay= 0.1 m (one increment only between 2.6 m and 2.7 m) Take n = 0.018.
Find the discharge through a given canal as shown.: A 116.85 m³/s 1 Take Manning's, = 0.016 and Bed slope = 625* B 139.25 m³/s C 68.95 m³/s 3m- D 97.85 m³/s -8m- 1.5
Q4/ A trapezoidal open channel. The following data are available: 1- Cross -sectional area of flow A = 108 (m') 2- Wetted perimeter P = 120 (m) 3- Longitudinal slope of bed level So = 0.0001 4- Bed width B = 4 (m) 5- Width of channel at water level w = %3D %3D = 4B (1/3) 6- n = 0.025 {s/m5)} Find the value of flow rate Q in the channel.
Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16ft and water depth of 4.5ft. The channel bottom drops 0.1ft every 100ft. Length, n=0.015 Compute the flow rate in ft3/s (using Manning) Group of answer choices 862.32 683.22 386.23 386.32
A rectangular channel is to carries 1 m3/s. Determine the most cost effective cross-sectional dimension of the channel – width and depth. The slope of the channel is 0.01. Neglect free board. Mannings n = 0.011.
A trapezoidal channel has a bottom width of 6 m and side slope of 2 horizontal and 1 vertical when the depth of flow is 1.2 m. When the flow is 20.40 m3/s, compute the slope of the channel if n = 0.014. Select the correct response: 0.00940 0.00490 0.00049 0.00094
It is desired to transport 20 cfs of water through a rectangular finishedconcrete (n = 0.012) canal that can be at most 5 ft wide. The slope of theland through which it passes is 0.0004. The depth of water, in ft, thatshould be expected is nearest: A. 1.83B. 1.28 (Incorrect Answer)C. 1.63 D. 1.01
Q5/A Triangular open channel. The available data are: Q = 13.5 (m³/s) v = 1 (m/s) n = 0.025 So = 0.0001 Z = 1.5 F.B = 0.8 (m) Find: Depth of water in the channel y. Width of the channel at the level of ground surface Wr.
See figure below Surt Pol Level rectangular channel with d1 = 5 ft d2 15 ft Q/B= 37 8 cfs/ft bed slope 0.0015 Calculate AE-1 distance between 1 and 2 2
Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16ft and water depth of 4.5ft. The channel bottom drops 0.1ft every 100ft. Length, n=0.015 Compute the flow rate in ft3/s (using Manning) 386.32 683.22 386.23 862.32
of trapezoidal section has to be √3 excavated throught A power Canal hard Clay at the least cost Determine the dimensions of the Channel given, discharge equal to 14 mm/s, bed slope 1/2500 Manning's n= 0.02 1 Z=