ong Stag 2. The following data relate to an inclined venturimeter: Diameter of the pipe line = 400 mm 1600 mm- Throat diameter = 200 mm Reading of the differential manometer =50 mm The co-efficient of the meter = 0.98 50 mm Determine the rate of flow in the pipe line. Oil (sp. gr. 0-7) Mercury (sp. gr. = 13-6) Inlet

ong Stag 2. The following data relate to an inclined venturimeter: Diameter of the pipe line = 400 mm 1600 mm- Throat diameter = 200 mm Reading of the differential manometer =50 mm The co-efficient of the meter = 0.98 50 mm Determine the rate of flow in the pipe line. Oil (sp. gr. 0-7) Mercury (sp. gr. = 13-6) Inlet

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An oil having specific gravity of 0.926 and viscosity of 350 Saybolt seconds flow through a 3//-diameter pipe orifice placed in a 5^-diameter pipe. The differential gage registers a pressure drop of 21.5 psi. Determineflow Q. Ans. 1.93 CFS
Q.2 a) A vertical venturimeter of d/D ratio equal to 0.8 is fitted in a 150 mm diameter pipe. The throat is 200 mm above the inlet. The venturimeter constant = 0.92. Determine: (i) Pressure difference as recorded by two gauges fitted at the inlet and throat. (ii) Difference on a vertical differential mercury manometer (sp. gravity = 13.6) when a liquid of sp. gravity 0.8 flows through the meter at the rate of 0.05 m^3/s. *
oblems: 1. A horizontal pipe, 1 ft. in diameter, tapers gradually to 8 in. in diameter. If the flow is 500 cu ft. of water per minute, what is the difference between the pressures at the two sections? Ans. PA - PB = 443.63lb per sq ft 2. Water flows through a horizontal pipe at a velocity of 50 ft. per sec. Owing to the pipe gradually expanding to a larger size, the velocity decreases to 35 ft. per sec. What is the difference between the pressures at two points, one in each size of pipe? Ans. Pg - PA = 1,236. 75 lb per sq ft
Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available. choices: a. 19.36 b. 17.23 c. 4.64
The ratio of entry diameter with exit diameter is 0.4 in a control volume of pipe segment. What is the corresponding ratio of entry to exit velocity? Recall Q1=Q2 and v1A1=v2A2 Correct answer has a margin of 0.1 from exact answer.
The longest pipe run for a hot water system is 100 m. If the pressure rise through the pump is 35 kPa, then the pressure drop per one meter in system is إختر أحد الخيارات: Pa/m 233.3 .a O Pa/m 400 .bO Pa/m 250 .c O Pa/m 375 .d O
A glass manometer with oil as the working fluid is connected to an air duct as shown in the figure. I) Will the oil levels in the manometer be as in a or b? II) What is the response if flow direction changes? III) If the manometer is replaced with a piezometer at a smaller cross section, oil levels will be according to a or b? Flow Flow (a) (h) O a. I) a; II) a; III) b O b. I) b; II) b; III) a O c. I) a; II) b; III) b O d. 1) b; II) a; III) a
H. 3 2. What are the relative advantages of using a Venturi meter to measure flow compared with an orifice meter?
2. A centrifugal pump installation has been designed to discharge 0.126 ?3/? of brine (sp.gr. = 1.2). The suction pipe is 305 mm and is at the same level as the discharge pipe which is 203 mm in diameter. At the centerline of suction flange, the vacuum is 154.2 mm Hg. The discharge pressure gauge reads 0.1379 MPa and is connected 1.22 m above the discharge flange centerline. The pump is driven by a 35 KW electric motor that will not carry overload and has an efficiency of 82%. There is no significant head loss. The design conditions have changed, and is now desired to increase the capacity of the pump by increasing the speed. The motor is so designed that its speed maybe increased but its power cannot exceed its design rating. Assuming the pump efficiency to remain constant, how much can the pump capacity be increased without overloading the motor?
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.. A cylindrical tank 5 ft high has a constant diameter of 4 ft is full of water. The tank has a hole2. A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a holein its bo]om that measures 0.1ft^2. All losses are insignificant. How long will it take for the tankto empty? Note that you can NOT assume a staLc head and constant flow rate because thewater head in the tank decreases as the water flows out of the tank (A) 35 sec(B) 70 sec(C) 105 sec(D) 140 sec
%VY l. lin. 3. N Sheet 1.pdf → Sheet 1 Page 1 of 2 Q1/ An orifice meter is to be calibrated for the measurement of the flow rate of a stream of liquid acetone. The differential manometer fluid has a specific gravity of 1.10. The calibration is accomplished by connecting the orifice meter in series with a rotameter that has previously been calibrated for acetone, adjusting a valve to set the flow rate, and recording the flow rate (determined from the rotameter reading and the rotameter calibration curve) and the differential manometer reading, h. The procedure is repeated for several valve settings to generate an orifice meter calibration curve of flow rate versus h. The following data are taken. VALVEX Flow Rate D (ml/s) Manometer Reading h(mm) 62 10 15 87 107 20 123 25 30 138 151 1- For each of the given readings, calculate the pressure drop across the orifice, AP (mm Hg). 2- The flowrate through an orifice should be related to the pressure drop across the orifice by the formula. V =…
Q No. 5: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no losses. Note : Please Solve as Per Question's Statement. Need a Neat and Clear Solution.See Attached Picture For Detail .