Outside air at a temperature of 25° C is drawn into the duct and then heated along the ductat 228 kJ/kg. At section 1 the temperature is T = 15° C and the absolute pressure is98 kPa. Neglect friction. (Figure 1)Part AFigure50 mm-2 mDetermine the Mach number at section 2.Express your answer using three significant figures.ΜΕ ΑΣΦvecM2 = 0.91SubmitPrevious Answers Request Answer× Incorrect; Try Again; One attempt remaining1 of 1Part B Complete previous part(s)Part C Complete previous part(s)Provide Feedback?

Answered: Image /qna-images/answer/13a3ff5b-b238-4a67-93ad-e9656177215a.jpg

Answered: Outside air at a temperature of 25° C…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

oll, s = 0.80 kerosene,s = 0.82 A manomoter is used to moasuro tho s = 0.0012 pressure of air in shown. Solve the pressure at point A given the following hoights: the pipe as Air = 0.35 m,h2 = 0.38 m, h, = 0.20 m, %3D h4 = 0.50 m, hs = 0.10 m, h6 = 0.30 m hz hy h3 ho Water Mercury Mercury
Šubiect No. Bubject Date No. An open manometer, shown în the Dright figure, is in stalled to measure D pressure in a pipe canrying (sp.gr=0.82). If the manometer liquid is carbon tetra chlovide (sp.gr=lo6o) determine the pipe pressure (in meters oil of water- colunn heig ht) an oil 11 Air > 66 Cm imanometer liquid
2- Oil (p = 80o kg/m2) flow through a 5omm-diameter smooth pipe at a velocity of 2m/s, the pressure drop due to friction loss in the pipe 5023 pa. The pipe length is 1om. a- Calculate the friction factor, f. %3D b- Determine whether the flow is laminar or turbulent. C- Calculate the oil viscosity. (b) o.0157 (d) 487x10-6 N s/m2]
IL. Q2-1 [5 Points]:A fluid has an absolute viscosity of 0.048 Pa-s and a specific gravity of 0.913. For flow of such a fluid over a solid flat surface, the velocity at a point 50 mm away from the surface is 1.467 m/s. Calculate the shear stresses at the solid boundary (N/m) 0.67 1.2 3.35 0.97 1.41 3.03 1.35 1.79
Water backs up behind a concrete dam as shown in figure Leakage under the foundation gives a pressure distribution under the darri as indicate If the water depth, h, is too great, the dam will sopple over about its toe (Point A) For the dimensions given, determine the factor of safety agarest overtuming moment if L-120 fh and h - 50 n. Base your analysis on a unit length of the dam The specific weight of the concrete is 150 ib/tt3 Water
FLUID FLOW IN PIPES I. Proving. SHOW THAT 2. T= y (hf)D fyv² 4L 8g
In the figure, in +he water 0,1M -(2) Alow in the T-shapped pipe inthe horizental plane, の3m the flow velocityinthe Ist section 1s v, 4MIS, +he relative pressure is pi = 3 kg lkm? Find the X andy components of the force that the fluid acts on the T- pipe segmant, the ossiming Alow at fluid ideal if the 2nd cross Section Vz =4mls %3D
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter [Est =30,000 ksi, Eal=10,000 ksi]. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips (1) |D C 18 kips B 34 kips 60 in. 40 in. 30 in.
After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of water. What is the maximum permissible value of d so that the water level will just barely reach the brim of the glass, as shown? Assume that the SG of the glass is 2.55. icin-2 in 4 in. SAE oll Water
Part 2Two pipes are connected by a manometer as shown. Determine the pressure difference, between the pipes in kPa.
Q5: The compart ments (B) 4 Cc) in figure below are closed & filled with air. When the gauges (A) f (D) read as indicated, what should be the value of Cx) for gaugeCE)? (Mercury in each U-tube gauge) 2.07 bar 254 Air Air E.
5. For the setup shown in figure below calculate the pressure at A. assume standard atmospheric pressure is 101.3 kPa Air H₂O W 600 mm 200 mm 140 mm 90mm -Oil specific gravity-0.83

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS