3: Ammonia gas(A) and nitrogen gas (B) arethrough a straight glass tube 2-0 ft long with an inside diameter24.4mm at 298 K and lol.32 Kla. Both ends of the fube areConnected to large mixed chambers at lol.32 k Pa. The Partialpressure of NH3 is constant at 20 kPa in one cham ber and 6.66 KPein the offer.@ Calculate the diffusion of NHs@ Calculate the diffusion of N2O Calaulate the partial presures at pomt (o.305 m) it the fubedffusing in GunterdBhe

Answered: Image /qna-images/answer/3a960794-9c43-4bd9-9039-7df276798ba9.jpg

P3: Ammonia gas(A) and nitogen gas (B) are diffusing in Gunterdhs straight glass tube 2.0 ft long with an inside diameter through 24.4 mm at 2q8 K and lol.32 Kla. Both ends of the tube are Connected to large mixed chambers at lol.32 kPa The Partial pressure of NH3 is canstant at 20 kPa in one cham ber and 6.66 KPe in the ofher. Calculate the diffusieon of NH3 O Calculate the diffusion of Na E Calausts the partial trsur s et pont (o.305 m) in the febe a

P3: Ammonia gas(A) and nitogen gas (B) are diffusing in Gunterdhs straight glass tube 2.0 ft long with an inside diameter through 24.4 mm at 2q8 K and lol.32 Kla. Both ends of the tube are Connected to large mixed chambers at lol.32 kPa The Partial pressure of NH3 is canstant at 20 kPa in one cham ber and 6.66 KPe in the ofher. Calculate the diffusieon of NH3 O Calculate the diffusion of Na E Calausts the partial trsur s et pont (o.305 m) in the febe a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A 0.4 mm diameter glass tube is inserted into kerosene at 20°C (p=804kg/m³). The contact angle of kerosene with a glass surface is 26°. Determine the capillary rise of kerosene in the tube. (The surface tension of kerosene-glass at 20°C is 0.028 N/m)
1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x10-3 m/s. If the surface area of the plate in contact with the liquid is 0.6 m2, determine the approximate viscosity of the liquid. В B' 3 mN 4 mm A
(1) ū = -2xyi ラ= y? - x2 w=5k K (1) V = – 2tr 2tr a-) Is the flow field given in (1) incompressible? b-) Is the flow field given in (1) irrotational? c-) Determine the vorticity for the flow field given in (II). d-) Make a sketch for the folloing fluid propeties by combining the forced and free vortex. Vel る
vertical axis circular cylindrical storage tank, fabricated from stainless steel has a total height of 8meters and a radius of 1.5meters and is filled to a depth of h - 6meters of wine. An inert gas occupies the 2m height ho, above the free liquid surface and is pressurized to a value of 96kPa. The working stress in the steel is 58Mpa. The specific weight of the wine 9.8kN/m^3 1. What is the required wall thickness of the tank?
Find the capillary rise in the tube shown below for an ethylalcohol-air-glass interface if the tube radius is 1mm and surface tension of ethylalcohol is 0.022N/m and sg=0.79.
In horizontal pipe, which of the following is constant? Pressure headElevation headVelovity head 12
Q1: Derie an epressin for the shear stress at the pipe wall when an incompressible faid flows draugh a pipe wnder pressure. Use dinmsional ana)sis witk the following siguißcant parameters: pipe diameter D, flow velociy V, and vicenity and density p of the fuid. Q2: : Use dinensional analysis to derive as epression for the power develaped by an engine in terms of the torque T and rotartive speed u.
The same open tank now contains three immersible liquids as shown. Because of the system geometry, piezometer A contains liquid A, piezometer B contains liquid B, and piezometer C contains liquid C. Determine (a) the gage pressure at the interface between liquids A and B, at the interface between liquids B and C, and at the tank bottom; (b) the elevation of the liquid surface in piezometer A; (c) the elevation of the liquid surface in piezometer B; (d) the elevation of the liquid in piezometer C. (e) redraw the sketch and show the liquid to the correct elevation in each tube.
7. A PFR is not meeting effluent requirements so baffles are going to be added to the tank to increase contact time. The tank is 12 ft deep, 40 ft wide, and 120 ft long. The engineer is going to add long baffles to the tank. The baffles will be 90% of the tank length. If the current HRT is 0.5 d, and the influent concentration is 9 mg/L with an effluent limit of 1.5 mg/L, how many baffles need to be added? Assume k-1.98/day
6. Find the capillary rise in the tube for a mercury-air-glass interface with 0 = 130° if the tube radius is 1.0 mm. c. -12.3 mm d. –5.0 mm a. 4.12 mm b. -6.33 mm 7. A 1-inch-diameter soap bubble has an internal pressure of 0.0045 lb/in? greater than that of the bubble of the outside atmosphere. Compute the surface tension of the soap-air interface. a. 0.00675 lb/ft b. 0.00123 lb/ft c. 0.00351 lb/ft d. 0.00127 lb/it
In the figure, in +he water 0,1M -(2) Alow in the T-shapped pipe inthe horizental plane, の3m the flow velocityinthe Ist section 1s v, 4MIS, +he relative pressure is pi = 3 kg lkm? Find the X andy components of the force that the fluid acts on the T- pipe segmant, the ossiming Alow at fluid ideal if the 2nd cross Section Vz =4mls %3D
SOLUTION MUST BE HANDWRITTEN a.) The hydrostatic force due to linseed oil F1. b.) The hydrostatic force due to castor oil F2. c.) The hydrostatic force due to water d.) The net hydrostatic force acting on the gate Fnet