Pipe No. Length - m Diameter - cm 1 1000 90 2 500 50 600 40 4 800 700 75

Q: 2. Determine the discharge in each pipe of the network shown in the figure by using the Hardy- Cross…

A: Given: Consider the loop given and assuming n=2 for all pipes. In Hardy Cross Method, Q values are…

Q: Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter…

A:

Q: The properties of three pipes connected in series are tabulated below. (a) What is the head loss…

A:

Q: A water pipe is given as shown in the figure. Given: Point 1: D1 = 14.1 in, p1 = 20.8 psi, v1 = 4.2…

A:

Q: A discharge of 30 liter/s of water is flowing in the pipeline shown in the figure, what pressure…

A: For the given pipeline,

Q: With velocity of 10 m/s in the 347 mm diameter pipe in the figure shown, determine the discharge in…

A: Given data: Velocity in pipe 1=10 m/s f=0.034 L1=345 m,    D1=347 mmL2=477 m,    D2=571 mmL3=598 m,…

Q: Two hydraulic cylinders in a hydraulic system are shown in Figure 3.2. The inner diameters of the…

A: In piston A, given Velocity of flow = V1 = 1.25 m/s diameter = d1 = 75 mm = 0.075 m…

Q: In the figure, a pipe system in parallel is with a total flow of 400lit/s. determine the division of…

A:

Q: Driven by pressurized air in a tank, water flows through pipes (L1₁ = 40 m, L2 = 80 m, L3 = 20 m) of…

A: Given: A flow of water through pipe of length L1, L2 and L3 as shown in the figure Dynamic…

Q: Question: As shown in the figure, water enters and leaves a U-shaped piece of pipe in the horizontal…

A: Solution

Q: 2) In the figure shown pipes are in parallel connection with properties given. If the flow into the…

A:

Q: The discharge through a 75-mm diameter orifice at the bottom af a large tank was measured be 1.734…

A: Given data  Actual Discharge  Diameter  Head

Q: The duct shown in the figure has a reduction of 1 to 2, discharge to the atmosphere in section 3,…

A: Flow rate is defined as the rate at which fluid  is flowing in a given tube or section having…

Q: 4. Two pipes of diameters d1 and d2 converge to form a pipe of diameter 2d. If the liquid flows with…

A: GIVEN: Two pipes of diameters d1 and d2 converge to form a pipe of diameter 2d. If the liquid flows…

Q: Using the value of Cd, which you have obtained by experiment, determine the throat diameter of a…

A: Solution  Given Data:- Pipe Diameter = 0.6 m  Differential Head = 0.8 m Flow Rate = 0.4 m3/s  Find-…

Q: For the flow shown in the figure below, the stream function is = {4ri sin( 0)} where r is in meters.…

A:

Q: In the figure, the pipe exit losses (1.5)v2/2g, where v is the exit velocity. What is the exit…

A:

Q: Notice in the figure, a free jet falling from a nozzle of triangular cross section. After it has…

A: Given: The entrance of the nozzle is in triangular shape with length sides l=0.19 ft. The exit…

Q: Determine the difference in pressure between the centerline points A and B in the two pipelines as…

A: The manometer is used to measure the pressure of liquids or gases. Some types of manometers are used…

Q: Notice in the figure, a free jet falling from a nozzle of triangular cross section. After it has…

A: Given:- a=0.19 ft, h=2.7 ft, d=0.11 ft To find:- Volume flow rate

Q: The figure shows a pipe network with initial discharge that is used to find the discharge in each…

A: The fluid mechanics is the subject of designing which will be helpful in many designing discipline.…

Q: As shown in the figure, water flows through the horizontal branching pipe at a rate 280 L/s. Viscous…

A: If you want any specific question to be answered then please specify the question number or post…

Q: 3. For the cross section of a culvert shown in figure, compute the moment of inertia about the…

A:

Q: In the figure, a 50 mm pipeline leads downhill from a reservoir and discharges into air. If the loss…

A:

Q: 3 2 Figure Q1

A: Given : Height at 1 = 2.4 m Width, b = 4 m Discharge, Q = 12 m3/s

Q: 5. Find the discharge of water through the channel shown in figure. Take the value of Chezy's…

A:

Q: The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be…

A: The internal energy of a fluid due to pressure exerted on its container is known as pressure head…

Q: a discharge of 700L/s flows through a pipe having a diameter of 400mm and a length of 60m long.…

A:

Q: The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be…

A: Bernoulli's Equation: Bernoulli’s equation formula is a relation between Kinetic energy, pressure,…

Q: The flow from A to E is 0.280 cum/sec. Using n = 0.058 Pipe 1 (Diameter and Length): 450 mm, 300 m…

A: Assuming n as 4f  n = 0.058 = 4f Total head loss From A to D is  = 165.861 meters

Q: (5 pts) From the figure below, pick the best impeller size for a pump with a flowrate of 40U gpi The…

A: Given, Flow rate (Q) = 400 gpm

Q: Example 15.5 In a flow through a rectangular channel for a certain discharge the Froude 2/3 numbers…

A:

Q: Question#4\\ As shown in figure 3, when the flow rate at pipe (No.4) equals (0.6 m/sec). Calculate…

A: Solution:-Given Data,Flow rate in pipe 4=0.6 m3/secThe diameter of pipes are ,D1=450mm=0.45…

Q: A discharge of 750 liters/sec flows through a pipe having a diameter of 400 mm and a length of 65 m…

A:

Q: Water flows through a 75 mm diameter pipe at a velocity of 3 m/s. Find the mass flow rate in kg/sec…

A:

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given data,  n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 in To find…

Q: A triangular pipe network is shown in the figure. Q=100 A r=1 B Q=70 r=2 The head loss in each pipe…

A: Given- head loss hf=rQ1.8values of r-for AB=1for BC=2

Q: Qs/Three pipes No. (1), (2) and (3) are connected in series as shown in Figure No. (4). Find flow…

A: To find flow rate

Q: Question: Water is flowing in the vertical pipe system shown in the figure. Water exits to the…

A: The given figure is shown below:

Q: Water flows from the rectangular outlet as shown in the figure. Estimate the flow rate per unit…

A: The pipe flow always follows Bernaullis Equation i.e discharge at all the section will be equal. But…

Q: Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are…

A: Calculate entry loss and friction loss for the first pipe:

Q: Water (p =1000 kg/m³) is flowing through a tube with the constant surface area as shown in the…

A: Given:

Q: 3250 ft of 12 in 2 2750 ft of 21 in 2250 ft of 10 in 4750 ft of 27 in A 1 + B 3 -- C 5 D 2750 ft of…

A:

Q: Three pipes are connected in parallel. The difference in heads in each pipe is 40 m. Pipes Diameter…

A:

Q: In the figure shown pipes are in parallel connection with properties given. If the flow into the…

A:

Q: ... L = 500m D = 550mm L = 530m D = 550mm L= 550m L= 540m D = 600mm Q = 0.83 m3/s D = 500mm 6 A В L…

A:

Q: 12 litre/s 4.5 litre/s in a pipe system shown below. The diameters of all pipes are 150mm. 8u flow…

A:

Q: A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown in the…

A: Given 12 inch by 6 in venturimeter

Q: The total head loss in the pipe system shown in the figure below is 15 m. Assume f= 0.02 for all…

A:

Q: A tube of diameter 25 mm is used (as shown in the below figure) as a siphon to discharge water from…

A: Given data, Diameter of tube=25mm Atmospheric pressure=101.325kPa

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.