Prob. 2:- A U-tube acting as a water tank is shown in the figure. Determine: (a) Velocity of water leaving at (2) (b) Pressure at point (A) Assume frictionless steady and incomprensible flow, and assume that the reservoir is very large compared to the pipe. (g = 9.8 m/sc0²) 2₁- A PA 2=0 7.016 V=? 8m

Prob. 2:- A U-tube acting as a water tank is shown in the figure. Determine: (a) Velocity of water leaving at (2) (b) Pressure at point (A) Assume frictionless steady and incomprensible flow, and assume that the reservoir is very large compared to the pipe. (g = 9.8 m/sc0²) 2₁- A PA 2=0 7.016 V=? 8m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity profile of a liquid flows through the z direction of the vertical tube (figure right) with the radius n is given as; 1 dp (r2 – r3) 2µ dz Vz Specify the max imum velocity and derive an expression for the average velocity.
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
For a pitot tube given in the figure, obtain a relation that describes velocity at point X (Vx) assuming that it is an ideal fluid. To do that, follow the steps: - Define the pressure at point X - Define the pressure at point O - Write the Bernoulli equation between points X and O and explain how you obtained the relation that describes velocity at point X (Vx) for this ideal fluid.
A tank with radius (1m) and a height of (4m) is initially filled with water. Then the hole at the bottom of the tank (shown in the figure) is opened and the water flows out by gravitational. Find the time required to fill an (8 m³) vessel below the tank. • Use the gravitational acceleration g = 9.807 m\sec². R= 1 m 2 m 2 m Cd = 0.9 a =2 * 10-3 m? Vessel of 8 m3
The cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.2 m at the bottom of the tank. a. What is the time required for half of the water in the tank to drain after the outlet line is opened?b. The flow velocity of water from the bottom of a water tank is related to the height of the water in the tank, and this relation is v² = 2gh where v: (m / s) linear flow velocity, g: gravitational acceleration (10 m / s2) and h: (m) height.
Q2/ A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m) as shown in figure below. The suction pipe is 45 m long ( = 0.024) and 35 cm in diameter. The delivery pipe is 950 m long (f = 0.022) and 25 cm in diameter. The head discharge relationship for the pump is given by H, = (90 – 8000 Q*), where H, in m and Q in m³/s. Calculate the discharge in the pipeline and the power delivered by the pump. Delivery pipe. elevation 170 m Suction pipe, elevation- 110 m Good Luck Rasha H. Salman
In the depot in the figure, 1200 kg / m3 of oil is compressed with air. Calculate the flow rate of the oil flowing through the d diameter pipe. (The cross-sectional area of the container containing the oil is much larger than the cross-sectional area of the d diameter pipe.) (H1 = 2m, h2 = 30 cm, ød = 6 cm PHa = 13600 kg / m3) Atmosfer Hava ha hi Civa (Hg) |||| | ||| ||
2500kW power is generated shown in the Figure with a water flowrate of 20 m3/s. The head loss for the entire flow is 2.5m. (a) Find the pressure difference P1 - P2 across the turbine. (b) Find h You can neglect the head loss between point 1 and 2.
The Water is flowing through a pipe having diameter 350 mm and 210 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 25.85 N/cm? and pressure at the upper end is 11.6325 N/cm? & the rate of flow through the pipe is 40 lit/s. Draw a neat diagram and determine the following: 1.Velocity head at bottom of the pipe in m/s. 2. Velocity head at top of the pipe in m/s. 3. The difference in datum head between top & bottom in meter of water - 4. The difference of pressure head between bottom to top end in meter of water.- The velocity of flow of water at the bottom in m/s.
Nadeen is washing her car, using a nozzle similar to the one sketched in Fig. 4-8. The nozzle is 3.90 in (0.325 ft) long, with an inlet diameter of 0.420 in (0.0350 ft) and an outlet diameter of 0.182 in (see Fig. 4–9). The volume flow rate through the garden hose (and through the nozzle) is V = 0.841 gal/min (0.00187 ft/s), and the flow is steady. Estimate the magnitude of the acceleration of a fluid particle moving down the centerline of the nozzle.
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p° = 1.013*10° Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m³ Poil = 800 kg/m³ Psand = 200 kg/m³ Po h3=12 cm hy=12 cm hs al2cm oiL Pa h=5 cm h2 = 6 cm Sand water
The cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.1 m at the bottom of the tank. What is the time required for half of the water in the tank to drain after the outlet line is opened? The flow velocity of water from the bottom of the water tank is related to the height of the water in the tank, and this relationship is expressed by the formula v: (m / sec) linear flow velocity, g: gravitational acceleration (10 m / sec2) and h: (m) height.