Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as shown. Each copper rod has an area of 900mm2 and E=120GPA, and the allowable stress is 70MPa. The steel rod has an area of 1200mm2, E=200GPA and the allowable stress is 140MPA. Determine the largest load P which can be supported.

Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as shown. Each copper rod has an area of 900mm2 and E=120GPA, and the allowable stress is 70MPa. The steel rod has an area of 1200mm2, E=200GPA and the allowable stress is 140MPA. Determine the largest load P which can be supported.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
8 KN 2m 3m 6KN. Am 3m, 3m A B 2m 6KN cross-Section 300mm 150mm Only considering stresses that are normal to the cross-sections you're designing. Where omax is the maximum value of stress developing in the cross-sections. Calculate omax
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
fxplam how the to tal stress at a be determined from the figure below distance z Com ground surface d1 layer 1 d2 layer 2 Iz layer 3 z - d1 - d2
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
Q1 A truss system is shown in Figure Q1. It is loaded at joints D and E as shown. The truss members are to be manufactured from Aluminium Alloy cylindrical bar with a tensile yield stress of 300 MPa, a compressive yield stress of 200 MPa, and Young's Modulus of 70 GPa. 1.5m 1.5m A B 4001 10 KN 3m Fig. Q1 E 水 20 KN 1.5m D ➜ (a) Show that the truss system can be described as statically determinate. (b) Draw a Free Body Diagram of the truss and determine the reactions at the supports. (c) Use the METHOD OF JOINTS to determine the load in each member of the truss, indicating whether they are tensile or compressive.
E- 10IGPA A,-2 cm? 1) Determine the nodal displacements, average element stress values and support reactions dividing the bar into five elements (Use both the elimination method and E-69 GPa 4,-Sem 20kN E-73GP E-10IGPa penalty approach handling boundary conditions.) 50 cm- 40 cm 50 cm