Problem 2: A solid circular drive shaft with a diameter of 0.5" transmits a torque of 200 in-1bf and supports a maximum bending moment of 120 in-lbf. The driveshaft is made of steel (Sy = 50 ksi). (a) What is the safety factor against yielding using the max. shear stress criterion? Brye Zooorlst Way of 120m-1 of Shule Sponsi Safety fuctor agriax yollung using mat, Shar Stress Eriturlan. n= What is the safety factor against yielding using the max. distortion energy criterion?

Problem 2: A solid circular drive shaft with a diameter of 0.5" transmits a torque of 200 in-1bf and supports a maximum bending moment of 120 in-lbf. The driveshaft is made of steel (Sy = 50 ksi). (a) What is the safety factor against yielding using the max. shear stress criterion? Brye Zooorlst Way of 120m-1 of Shule Sponsi Safety fuctor agriax yollung using mat, Shar Stress Eriturlan. n= What is the safety factor against yielding using the max. distortion energy criterion?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
Q5: A steel shaft is to transmit a stable torque of 1400 Nm to the steel spur gear through a Type B square end key with the dimensions L=140 mm and b=14 mm. What should be minimum height of the keyto transmit the power safely. The allowable bearing stress is 90 MPa.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPaCrushing stress for bolt and key = 80 MPaShear stress for cast iron = 8 MpaSpeed N in Rpm = 500Power P in kN = 15
Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPaCrushing stress for bolt and key = 80 MPaShear stress for cast iron = 8 Mpa Speed N in Rpm = 200Power P in kN = 16
b) Design a self-aligning ball bearing with basic dynamic load rating of 69.5 KN to be used in the automobile industry to carry a thrust load of 1184 N. The expected life of the bearing is 5201 hours at 628 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.7 and radial and axial load factors are 1.4 and 2.2 respectively, the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Radial load acting on the bearing in N
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
3= Q + & 4qAnrm & Expert Q&A Design a shatt and tiange tor a Diesel engine in which protected type of flange coupling is to be adopted for power transmission. Th following data is availabl : for desig Power of engine = 75 kV speed of engine = 200 r.p.n maximum permissible stres?’ in shaft = 40 MPa; maximum permissible twist in shaft = 1° in length of shaft equal to 30 times the diameter of shaft; maximum torque =125 x mean torque; pitch circle diameter of bolts = 3 x diameter of shaft; maximum permissible stress in bolts = .20 MPa Il O >
Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotating orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. 6T td7 (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
A keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. (Ans: 4.33 cm)