Problem 2 Block A has a mass of 50 kg, and block B has a mass of 15 kg. They are stacked, connected by a cable running through frictionless pulleys, and positioned on a slope of e = 20'. The coefficient of kinetic friction between all surfaces of contact is µk = 0.35. The applied force is P = 65 N. Assume the force is sufficient for the blocks to start moving. A. Determine (a) the acceleration of block B, (b) the tension in the cord.

Problem 2 Block A has a mass of 50 kg, and block B has a mass of 15 kg. They are stacked, connected by a cable running through frictionless pulleys, and positioned on a slope of e = 20'. The coefficient of kinetic friction between all surfaces of contact is µk = 0.35. The applied force is P = 65 N. Assume the force is sufficient for the blocks to start moving. A. Determine (a) the acceleration of block B, (b) the tension in the cord.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Similar questions

The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the system be in static equilibrium 0n the rough inclined plane?
The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The 120-kg block A is suspended from a rope that runs around the fixed pegs B and C. The coefficient of static friction between the pegs and the rope is 0.25. Determine the range of the force P for which the system is in equilibrium.
Calculate the force P that is required to hold the 120-lb roller at rest on the rough incline.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.