Problem 3: For a sandstone reservoir, calculate the water saturation if the porosity (Ø) is (20 %), the resistivity of the formation water (Rw) is (0.09) and the true resistivity (R) is (15)? Problem 4: Calculate the water saturation for a sandstone reservoir if the porosity (Ø) is (10 %), resistivity of formation water is (Rw 0.02 Om) and the resistivity of the formation (R 20 Qm)?

Problem 3: For a sandstone reservoir, calculate the water saturation if the porosity (Ø) is (20 %), the resistivity of the formation water (Rw) is (0.09) and the true resistivity (R) is (15)? Problem 4: Calculate the water saturation for a sandstone reservoir if the porosity (Ø) is (10 %), resistivity of formation water is (Rw 0.02 Om) and the resistivity of the formation (R 20 Qm)?

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.17P

See similar textbooks

Similar questions

i. A sandstone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 6.21 cubic centimetres per second. The length of the core sample is 14 centimetres and its diameters is 6 centimetres. The pressure differential across the core sample is 15 atmospheric pressure and the water viscosity is 1.2 centipoises. Explain a method of how the permeability of low permeability reservoirs can be ii. improved.
A CID TXC test was performed on a sample of sand. At the end of consolidation, the back pressure was 140 kPa, and the cell pressure was 340 kPa. At failure, the deviator stress was (ơ1 – 03)f = 200 kPa. a. What was the total pore water pressure, u, at failure? b. Calculate the principle effective stresses, ơi' and os', at failure. c. Calculate the friction angle, d', for this soil.
نقطة واحدة نقطة واحدة نقطة واحدة The height of the capillary rise of water increases as particle diameter increases True O False O Normal fault is generated by compressive force True O False O The porosity is the ratio of void volume to total volume True O False O
2. Sand at a given relative density has a friction angle of approximately 33° (relatively low stress). When the sample is unsaturated at a given value of saturation (not given to you), the specimen has a negative pore pressure of 5 kPa. How tall a sandcastle "vertical" wall can you construct? What would happen to your sandcastle if the level of saturation suddenly increased? (Assume a total unit weight of 18 kN/m³)
Find Void ratio and porosity
Determine void ratio Porosity=0.142
A limestone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 4.15 cubic centimetres per second. The length of the core sample is 13.61 centimetres and its diameters if 7.13 centimetres. The pressure differential across the core sample is 25 atmospheric pressure and the water viscosity is 1.1 centipoises. Explain a method of how the permeability of this reservoir can be improved.
v; == 01): (A): Explain the factors that the coefficient of permeability depend on. (B): Prove that: Vg = %3D
Determine the equivalent liquid permeability for a core sample taken from a sandstone formation. Nitrogen was used to obtain the following data
b. Why is the moisture content multiplied by an adjustment factor to derive the Liquid Limit
The coefficient of permeability of the sand at a void ratio of 0.62 is 0.03 cm/s. The permeability of the sand at a void ratio of 0.48 is nearest to:
Calculate the effective stress in kPa for a soil element at a depth of 5 m from the uniform deposit. The water table is 2 m below the ground. Above the water table the degree of saturation is 0.6 the moisture content is 30 % and below the water table the water content is 40%