Problem 3. Using the T-s chart complete the following table of thermodynamic properties for water. Show yourstates on the chart.State1N34T [°C]500100P[kPa]200010.000v [m³/kg]h [kJ/kg]3445Phase [Quality if Applicable]Sat. vapor [x = 1.0]Saturated [x = 0.75]

Answered: Image /qna-images/answer/75dc3964-68e6-4f86-9e13-53e9854ec2cf.jpg

Problem 3. Using the T-s chart complete the following table of thermodynamic properties for water. Show your states on the chart. State 1 2 3 T[°C] 500 100 20 P[kPa] 2000 10,000 v [m³/kg] h [kJ/kg] 3445 Phase [Quality if Applicable] Sat. vapor [x = 1.0] Saturated [x 0.75]

Problem 3. Using the T-s chart complete the following table of thermodynamic properties for water. Show your states on the chart. State 1 2 3 T[°C] 500 100 20 P[kPa] 2000 10,000 v [m³/kg] h [kJ/kg] 3445 Phase [Quality if Applicable] Sat. vapor [x = 1.0] Saturated [x 0.75]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Complete the following Table for water. For each case, draw a separate T-v diagram and qualitatively mark each thermodynamic state on the diagram. Show all required calculations for full credit. p[kPa] T[°C] v [m³/kg] u [kJ/kg] X state h [kJ/kg] 2260 275 400 700 350 1 2000 20
In order to fnd the specifc heat c of an unknown substance, you place 75 g of the substance in a 30 g copper calorimeter that contains 65 g of water, all initially at 20 °C. You then add 100 g of water at 80 °C, and measure the fnal temperature of the system to be 49 °C. Assuming no heat is lost to the environment, what is c? [Answer: c = 2200 J/kg. K] 즈
2. Complete the blank cells in the following table of properties of steam. In the last column describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information; and, if applicable, give the quality. P[kPa] T[°C] v[m³/kg] а. 500 20 b. 500 0.20 с. 1400 200 d. 300 0.8
Complete the following table for saturated water. Temp T ("C) Pressure P Entropy s (kJ/kg.K) Quality x Phase description (kPa) 120 5000 [1.1]? [1.2]? [1.3]? 50 1000 [1.4]? [1.5]? [1.6]? 400 1800 [1.7]? [1.8]? [1.9]? [1.10]? 40 [1.11]? X = 0.9 [1.12]?
A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P) are given below. P[Torr] 100.0 P [Torr] 127.9 200.0 256.5 300.0 385.8 400.0 516.0 What is the temperature of the unknown fluid bath? explain and show all work please and write clearly
The Antoine Equation can be used to estimate vapor pressure at various temperatures for different substances using sets of empirically-derived constants. The equation can be written as: Where for water A = 8.07131, B = 1730.63, C = 233.426, T = temperature [°C], and P = vapor pressure [mmHg]. Note that with these constants the temperature and pressure must be provided in °C and mmHg, respectively. Using the Antoine Equation and the provided constants, what atmospheric pressure (provided in terms of % of standard atmospheric pressure) will permit water to boil at 75 °C?
|The following processes occurs in a rever sible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure X)bar at volume Y)m' to a pressure [Z]bar and specific volume (A]m'/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure [B/bar. 3-1: Reversible cooling at constant volume to the initial state.
Air A Water Calculate the gauge pressure, in kPa, at A, B, C, D in the reservoirs shown above. (Note that the reservoirs between A and B are connected.) Problem parameters: h1 = 1.1 [m] h2 = 0.3 [m] h3 = 0.4 [m] h4 = 0.5 [m] Density of water is 1000 [kg/m³]; Density of air is 1.225 [kg/m³]; g = 9.81 [m/s²] S.G. of oil is 0.89 h4 [m] h3 [m] h2 [m] Air B h1 [m] Oil
The following processes occurs in a reversible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure [X] bar at volume [Y] m3 to a pressure [Z] bar and specific volume [A] m3/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure [B] bar. 3-1: Reversible cooling at constant volume to the initial state. What are the final attempt values of X, Y, Z, A and B from the Part A of the eThuto Assessment. calculated formula similar question? X= ; Y= ; Z= ; A= ; B=
1. Refrigerant R-22 with the mass of 2 kg is located inside the sealed container, initially saturated vapor at 6.8 bar. Heat was added to refrigerant and final pressure reached 20 bar according to pv=const. Neglecting the kinetic and potential energy changes determine: Internal energy change in [J] Heat added to the refrigerant in [J] and work done by fluid in [J]. 3.draw the Temperature-volume diagram showing all stages. 4.What do you think about the final stage condition? Is it gas, liquid-gas, or liquid stage? Use energy balance equation and find all unknowns using the NIST webbook.
You must select a submerged centrifuge multicellular pump for a borehole on a worksite that requires a flow of 1.500l/s. The borehole itself is 150m deep (see figure 5). If the outlet pipe has the following properties, then: wwww wwwwwww Water outlet (open air) wwww Outlet pipe L = 200m Borehole wwwww Pump f= 0.04 D = 38mm Figure 5 Borehole and pumping schematic A) Choose a pump from those presented in figure 6 (you must select the most adequate model) if there is no local head-loss, only friction related head-loss. You must draw the complete characteristic curve for the pipe directly on figure 6.; B) Is cavitation an issue if NPSHrequired is 5m briefly discuss the results. C) Determine the supplied power output by the pump (in kW) as well as the absorbed power output when the pump reaches it's operational flow for the pump you have selected. | N.B. Hypothesize that water in the borehole is level with the pump intake. The pump intake is the same diameter as the outlet pipe. Patm-100…
Problem-1 Calculate the efficiency of Carnot heat engine working between high temperature reservoir(source) T1 , and low temperature reservoir (sink) T2, for each case as described in the following table. High temperature reservoir(source) T[K] 1000 Low temperature reservoir(sink) T2[K] Carnot Efficiency,Ncarnot 300 1000 150 1000 100 1000 400 1000 500 1000 600 1000 750 1000 950 1000 999 750 300 600 300 500 300 400 300 300 300 1000 -500