Problem 4: Inputs: ● ● ● ● ● L₁ = 13 in L₂ = 11 in h = 10 in F = 40 lb 0 35° (measured from vertical) There is a pin at A and roller at B. h F L₁ L₂ a) Compute the horizontal component of the reaction at A. Indicate direction with your boxed answer. b) Compute the vertical reaction at A. Indicate direction. c) Compute the reaction at B. Indicate direction. B

Problem 4: Inputs: ● ● ● ● ● L₁ = 13 in L₂ = 11 in h = 10 in F = 40 lb 0 35° (measured from vertical) There is a pin at A and roller at B. h F L₁ L₂ a) Compute the horizontal component of the reaction at A. Indicate direction with your boxed answer. b) Compute the vertical reaction at A. Indicate direction. c) Compute the reaction at B. Indicate direction. B

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.28P

See similar textbooks

Similar questions

Find the V-X and M-X diagrams. For the value of P use 182 kips. show all steps
please send handwritten solution Q4 part e f g h complete
GIVEN : W= 345 N Q°= 27 DEGREE R°= 50 DEGREE S°= 25 DEGREE SOLVE (a) AC= IN NEWTON SOLVE (b) BC= IN NEWTON SOLVE (c) CD= IN NEWTON PLS PLS SHOWS THE COMPLETE SOLUTION AND WRITES LEGIBLY AND ALSO INCLUDES THE FREE-BODY DIAGRAM. WRITE IN FOUR DECIMAL PLACES. TAKE NOTE : USE EQUILIBRIUM NOT LAMI'S THEOREM
please send handwritten solution Q4 part a b c
Graphical Method : Polygon Method F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Length and Angle 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %Error
I need the solution for 3-25
HCM-6 At the design speed Vo Dan's car can go around a banked curve of radius 150M and banking angle of 10.0° without any friction force. The car is shown as viewed from behind in the figure below. R=150m 10.0° a) Use the figure above to draw the free body diagram for the car. Also show on the FBD the direction of the car's acceleration and show coordinate axis directions. b) Write down newtons's second law in component form for the car. Use NO numbers for this part. c) Use your equations from step b) to find the design speed Vo.
Q3 / Draw the following spring with all dimensions in sheet (write down all the equations you used in the :drawing if found) D1 70 mm D2 50 mm L 125 mm d 10 mm Pitch 25 mm
solve/ show solution for given answer equations kb = (Ab*Eb)/ g and kc = (Ac*Ec) / g
Problem 1: Solve for the COG, Ix and Ix the composite figure. Ix for half circle: (- Ix for rectangle: bh%/2 2in そ 3in COG half circle; 4r Lin 2in 2in
Please solve the following problem following the steps highlighted
2) Block 4 slides in a slot in the fixed piece 1. Axis Q₂ of crank 2 is fixed on 1. Q₂₂A = 1 1/2 in., and AB = 4/1/2 Draw the mechanism, assuming limen- sions for 1, if desired, or use center lines only. Draw the four-bar linkage for this mechanism, properly rotate the linkage Q₂ ABQ400; Name each link, and show the finite and infinite cranks. Frind graphically the two extreme positions of 13, The axis of the pin by which link 3 is attached to the block 4.. Dimension the length of the stroke of B. Ans. 3& in. for scale 1:1