Problem 4: μk Ө @0 m VO The homogeneous disk of mass m and radius r is projected along the incline of angle with an initial speed vo and no angular velocity (cm=0). If the coefficient of kinetic friction is , determine the time duration of the period of slipping, the velocity v of the mass centre and angular velocity w of the disk at the end of the period of slipping. In addition, state the conditions for which the slippage will not cease.

Problem 4: μk Ө @0 m VO The homogeneous disk of mass m and radius r is projected along the incline of angle with an initial speed vo and no angular velocity (cm=0). If the coefficient of kinetic friction is , determine the time duration of the period of slipping, the velocity v of the mass centre and angular velocity w of the disk at the end of the period of slipping. In addition, state the conditions for which the slippage will not cease.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4 Problem A coin of mass m is left at the edge of a rotating disk, a distance r from the center. The disk is rotating at a constant angular rate . The coin does not slip and experiences a friction force with static friction coefficient us. Determine the maximum speed, v, that the coin can attain before slipping. Hint: The friction force is a constant #,N and solely responsible for the rotational motion. The maximum speed occurs when this static friction force is just enough to sustain the centripetal force (mass times the centripetal acceleration). Values: g = 9.81 m/s², r =2 m, μs = 0.3. r
Ruler of the "Porter" model, with the upper and lower arms of 178 mm each, fixed by a hinge 38 mm away from the center of rotation. The rotating balls have a mass of 1.15 kg each, and the axial weight affecting the bushing is 20 kg. The ruling commotion began =154. Elevation at 280rpm - The joints are at an angle of 30 to the vertical. Assuming that the force of friction is constant, find the minimum and maximum rotational speed when mg The angle of inclination of the arms to the vertical is 45
A min cage of mass 4t is to be raised with an acceleration of 1.5m/s2 by a cable passing over a hoist drum of 1.5m diameter. What is the power required when the load has reached a velocity of 6m/s, neglecting the inertia of the drum and weight of the cable, but allowing for bearing friction torque of 3kN at the drum? What is the power required at a uniform velocity of 6m/s
Given: A uniform slender rod is at rest upon a frictionless horizontal surface when a force (F) is applied in the direction shown. Assume that the rod has mass m and length L. A L Horizontal Plane Given that F = 74lb, L = 7.1 ft, mg = 4.6lb, and 0 = 73deg What is the component of acceleration of the mass at point G in the i direction? Answer: Check What is the component of acceleration of the mass at point G in the j direction? Answer: Check What is the component of angular acceleration of the mass in the k direction? (remember your signs) Answer: Check
Q/A circular disc of mass m and radius r is Qil 'connected to two springs. If it is free to roll onarough horizoutal surface without_slipping, use energy methad to calculat the System natural Trequency.
A Porter governor has equal arms each 250 mm long and pivoted on the axis of rotation. Each flyball has a mass of 10 kg and the mass of the central load on the sleeve is 50 kg. The radius of rotation of the flyball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Find the range of speed, when the friction at the sleeve is neglected. Select one: A. 35.4 rpm B. 25.4 rpm C. 15.4 rpm D. 45.4 rpm
Fixed Axis Rotation Example 4: (HW) Calculate the downward acceleration a of the 10-kg cylinder. The drum is a uniform cylinder, and friction at the pivot is negligible. Compare your answer with that obtained by ignoring the inertia effects of the drum. r = 250 mm 15 kg Ans. a = 0.769 m/s With Io = 0: a = 1.090 m/s2 8 kg 10 kg
Problem #2) The thin plate ABCD has mass 10kg and is held stationary in the position shown (p= 30°) by a wire BH and the two massless parallel links AF and DE. At t = 0sec, the wire is cut and the plate is released from rest; it immediately moves in a pure translation motion due to the system's geometric constraint by the links. Find the forces in each link immediately after the wire is cut. All dimensions are in millimeters. 150 A D -500 H B IC T 200
In Figure Q5, the 17 kg of circular disk is originally rotating with a clockwise angularvelocity, ω = 49 rad/s at the end of the link BC. Given the kinetic coefficient offriction, μk = 0.25 when the disk is then placed against the wall. (i) Draw the kinetic diagram of all forces exerted on the circular disk.(ii) Calculate the force of link BC.(iii) Calculate the angular acceleration of the circular disk.(iv) Calculate the time required to stop the motion of the circular disk,
The spool has mass, m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the radius R and the outer radius 2R. The coefficient of friction between the spool and the ground is mu. What it the critical force, Fcrit (force required to cause motion) applied at point B? If force= 2Fcrit what is the linear acceleration of the center of mass? If force= 2Fcrit what is the tension in cord AC?
10:57 68 Practice: A + In Fig 3-16, the two boxes have identical masses of 40 kg. Both experience a sliding friction force with Hk = 0.15. Find the acceleration of the boxes ng sin 30 30 and the tension in the tie cord. Fig. 3-16 Kimberly S •.. Niea Sama. & Princess Di.. & Kimberly S
7. 2) The lawn roller has a mass m = 55 kg and a radius of gyration about its gravitational center G, kG = 196 mm. It has a handle that connects to its center axle, and the handle is pushed forward with a force F = 420 N at a 45° angle. The coefficients of static and kinetic friction between the roller and the ground are us = 0.11 and Hk = 0.08, respectively. For the sets of parameters listed below, determine the magnitude of the roller's angular acceleration (in rad/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. F 45° 200 mm A