Problem 4: The pump in the figure below delivers water from the lower to the upper reservoir at therate of 2.0 ft /s. The energy loss between the suction pipe inlet and the pump is 6 lb-ft/lb and thatbetween the pump outlet and the upper reservoir is 12 Ib-ft/lb. Both pipes are 6-in Schedule 40 steelpipe. Calculate (a) the pressure at the pump inlet, (b) the pressure at the pump outlet, (c) the total headon the pump, and (d) the power delivered by the pump to the water.Discharge pipe40 ftSuction pipeFlowH Pump+10 ft

Flow rea of 6 in schedule 40 steel pipe, A=0.2006 ft2

Problem 4: The pump in the figure below delivers water from the lower to the upper reservoir at the rate of 2.0 ft /s. The energy loss between the suction pipe inlet and the pump is 6 lb-ft/lb and that between the pump outlet and the upper reservoir is 12 lb-ft/lb. Both pipes are 6-in Schedule 40 steel pipe. Calculate (a) the pressure at the pump inlet, (b) the pressure at the pump outlet, (c) the total head on the pump, and (d) the power delivered by the pump to the water.

Problem 4: The pump in the figure below delivers water from the lower to the upper reservoir at the rate of 2.0 ft /s. The energy loss between the suction pipe inlet and the pump is 6 lb-ft/lb and that between the pump outlet and the upper reservoir is 12 lb-ft/lb. Both pipes are 6-in Schedule 40 steel pipe. Calculate (a) the pressure at the pump inlet, (b) the pressure at the pump outlet, (c) the total head on the pump, and (d) the power delivered by the pump to the water.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pump in figure delivers water from the lower to the upper reservoir at the ft³ S rate of 2.0 The energy loss between the suction pipe inlet and the pump is 6 lb-ft/lb and that between the pump outlet and the upper reservoir is 12 lb- ft/lb. Both pipes are 6-in Schedule 40 steel pipe. Calculate (a) the pressure at the pump inlet, (b) the pressure at the pump outlet, (c) the total head on the pump, and (d) the power delivered by the pump to the water. 40 ft 10 ft Discharge pipe Suction pipe Pump Flow
Item#3 The oil tank for the hydraulic system of figure below is air-pressurized at 10psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to0.5HP. Find the pressure at station 3if there is a 28ft head loss between station 1 and 3. OIL LEVEL SG 0.9 1.5-IN- INSIDE DIAMETER 10 FT STRAINER ELECTRIC MOTOR M 2 FT PUMP 3 Q-30 GPM
Show the step by step solution. Thank you. 3. A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure 4-10. The loss of head from A to 1 is 3 times the velocity head in the 150-mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100-mm pipe. Compute the horsepower output of the pump and the pressure heads at 1 and 2 when the discharge is: (a) 12 L/s (b) 36 L/s
1. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 2.5 m/s. At A in the suction pipe, the pressure is -40 kPa. At B in the discharge pipe, which is 2.5 m above A, the pressure is 410 kPa. What horsepower would have to be applied by the pump if there were no frictional losses? 2. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 3.6 m/s. The pressure is -35 kPa at A in the suction pipe. The 150 mm pipe discharges horizontally into air at C. To what height h above B can the water be raised if B is 1.8 m above A and 20 hp is delivered to the pump? Assume that the pump operates at 70 percent efficiency and that the frictional loss in the pipe between A and C is 3 m.
1. A pump (Figure 4-07) takes water from a 200-mm suction pipe and delivers it to a 150-mm discharge pipe in which the velocity is 2.5 m/s. At A in the suction pipe, the pressure is -40 kPa. At B in the discharge pipe, which is 2.5 m above A, the pressure is 410 kPa. What horsepower would have to be applied by the pump if there were no frictional losses?
Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. a. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? b. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe?
Provide the diagram for the problem. Choose the correct answer and provide complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. A. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? a. 86%b. 65%c. 77%d. 50% B. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe. a. 45 lb/sb. 37 lb/sc. 52 lb/sd. 29 lb/s
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m. The impeller of the centrifugal pump has a diameter of 0.55 m and operates at 850 rpm. The uniform blade height is 51 mm. The water enters the pump parallel to the pump shaft with a flow rate of 0.16 m3/s. Take viscosity as 0.00112 N s/m2. Fig Q2: Piping system to pump water between two tanks. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What would be the shaft power required to turn the impeller if the exit blade angle is 31 degrees. b) Find the major losses in the system. Take the pipe Darcy friction factor as 0.055. c) Determine the difference in height between the water surfaces in the two tanks assuming that there are no losses within the pump.
The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m. The impeller of the centrifugal pump has a diameter of 0.55 m and operates at 850 rpm. The uniform blade height is 51 mm. The water enters the pump parallel to the pump shaft with a flow rate of 0.16 m3/s. Take viscosity as 0.00112 N s/m2. Fig Q2: Piping system to pump water between two tanks. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What would be the shaft power required to turn the impeller if the exit blade angle is 31 degrees. b)
The oil tank for the hydraulic system of figure below is air-pressurized at 10 psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to 0.5 HP. Find the pressure at station 3 if there is a 28 ft head loss between station 1 and 3.
For the single pump-pipe system below, what will be the changes for the operating point if we increase the pipe size but decrease the shaft speed of the pump? EB H₂ O The operating point will remain the same. O The operating point will occur either at a higher discharge or at a lower discharge, depending on the specific influence of each change. O The operating point will occur at a higher discharge. O The operating point will occur at a lower discharge.