Problem-5 A compression spring is made of a music wire of 2 mm diameter having a shear strength and shear modulus of 800 MPa and 80 GPa respectively. The mean coil diameter is 20 mm, the free length is 40 mm and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately...

Problem-5 A compression spring is made of a music wire of 2 mm diameter having a shear strength and shear modulus of 800 MPa and 80 GPa respectively. The mean coil diameter is 20 mm, the free length is 40 mm and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Prob 02: The two rods are used to support a crate with weight of 2kN. The rod are made of the same material and of the same diameter. If the failure tensile normal stress for this material is 200 mPa, what is the minimum required diameter for the rods in mm? (2 points) 45° 30°
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E = 69 GPa. The steel rod has a diameter of 22 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.7 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 9 mm to the left?
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B KN O
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E = 69 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 195 GPa. Assume a = 3.6 m, b = 1.5 m, and c= 0.8 m. What is the magnitude of load P that is necessary to displace point A 11 mm to the left? (1) (3) B (2) Answer: P = i kN
An aluminum [E = 10400 ksi] control rod with a circular cross section must not stretch more than 0.39 in. when the tension in the rod is 2310 lb. If the maximum allowable normal stress in the rod is 12 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = i (b) L= i in. in.
A damper square mat is supporting a dead load weight of 8 KN. Helical springs will be used to support the load located at a corners with shearing stress or 120. MPa at 20 turns. The spring has a deformation of 98.7 mm with a mean radius of 80 mm. Design the minimum diameter or the wire to support a load. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 63 GPa. The steel rod has a diameter of 15 mm and an elastic modulus of E= 195 GPa. Assume a = 4.0 m, b = 1.5 m, and c = 0.9 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a Answer: P = i (3) B D KN
the trolley of a small hoist is supported on a horizontal beam as shown. the maximum mass to be lifted is 6000kg the tie back is a round rod 33 mm in diameter the tensile stress in the is not to exceed 170 MPa the maximum elongation allowed for the tie back is 2.5 mm. determine the maximum dimemnsion L permitted
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN
1. Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 500 T1.2 190 3 35 Aluminium 400 18.9 22 70 Aluminium Steel 4m 2m
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-