Problem 6 An 02-series single-row deep-groove ball bearing with an 80 mm bore is loaded with a 5-kN axial load and a 9-kN radial load. The bearing has the basic dynamic load rating C₁0 of 70.2kN and basic static load rating Co of 45kN. The outer ring rotates at 500 rev/min. Use the Weibull parameters for Manufacturer 2: x₁=0.02; ; b=1.483. 0 = 4.459 and the application factor of 1.0. (a) Determine the equivalent radial load that will be experienced by this particular bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 15 kh.

Problem 6 An 02-series single-row deep-groove ball bearing with an 80 mm bore is loaded with a 5-kN axial load and a 9-kN radial load. The bearing has the basic dynamic load rating C₁0 of 70.2kN and basic static load rating Co of 45kN. The outer ring rotates at 500 rev/min. Use the Weibull parameters for Manufacturer 2: x₁=0.02; ; b=1.483. 0 = 4.459 and the application factor of 1.0. (a) Determine the equivalent radial load that will be experienced by this particular bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 15 kh.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder with a nominal 2.5 in ID, a 4.0 in OD, and a 3.0 in length is to be mated with a solid shaft with a nominal 2.5 in diameter. A medium drive fit is desired (as defined in Table 7-9). The cylinder and shaft are made from steel, with Sy = 100 kpsi and E = 30 Mpsi. The coefficient of friction for the steel interface is 0.7. a. Specify the maximum and minimum allowable diameters for both the cylinder hole and the shaft. b. Determine the torque that can be transmitted through this joint, assuming the shaft and cylinder are both manufactured within their tolerances such that the minimum interference is achieved. c. Suppose the shaft and cylinder are both manufactured within their tolerances such that the maximum interference is achieved. Check for yielding of the cylinder at its inner radius by finding the following: i. The pressure at the interface ii. The tangential and radial stresses in the cylinder, at its inner radius. iii. The factor of safety for static yielding of the…
A certain application requires a ball bearing with the inner ring rotating, with a design life of 25 kh at a speed of 400 rev/min. The radial load is 3.5 kN and an application factor of 1.5 is appropriate. The reliability goal is 0.90. Find the multiple of rating life required, Xp and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11-2, and estimate the reliability in use.
Answer this ASAP plz A double row angular contact ball bearing is used in the engine compressor to accept radial loads of 6000 N and axial loads of 3000 N, operating at 2400 rpm for an average life of 7 years at 8 hours per day. Assume that the shock load is light. Select the appropriate bearing number. Note: the equivalent dynamic load is the dynamic equivalent radial load times the service factor.
For the geared countershaft with an overhanging pinion at C, the force on gear A is FA = 600 Ibf, and the shaft is to run at a speed of 420 rev/min. Consider an application factor of 1.2, a desired life of 40 kh, and combined reliability goal of 0.95 Select and specify the bearing required a) An angular contact ball bearing for mounting at O and b) A straight roller bearing for mounting at B Gear 3 24 dia. Gear 4 10 dia. 20
The design load on a ball bearing is 413 lbf and an application factor of 1.2 is appro- priate. The speed of the shaft is to be 300 rev/min, the life to be 30 kh with a reliability of 0.99. What is the C10 catalog entry to be sought (or exceeded) when searching for a deep-groove bearing in a manufacturer's catalog on the basis of 106 revolutions for rat- ing life? The Weibull parameters are xo = 0.02, (0 – xo) = 4.439, and b = 1.483. %3D
A bearing with a is loaded with a 2-kN axial load and a 8-kN radial load. The outer ring rotates at 600 rev/min with prdicted desing life of 1000 h. a. Determine the equivalent radial load that will be experienced by this particular bearing. b. Determine the Dynamic load rating that will be used for bearing selection c. Make the selection ex (series type bore diameter outer bearing diameter)
Problem 2 A 02-series single-row deep-groove ball bearing with a 65-mm bore (see Tables 11–1 and 11– 2 for specifications) is loaded with a 10-kN axial load and a 15-kN radial load. The inner ring rotates at 500 rev/min. (a) Determine the equivalent radial load that will be experienced by this bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 20 kh.
1. Select a single row, deep grove ball bearing that carries a 35 mm diameter shaft. It carries an axial load of F. - 2000 N and a radial load F, = 8000 N. Outer race rotates and a life of 5000 hours at 120 rpm is expected. Verify your selection by a second iteration for dynamic load rating. 2. The journal bearing of a small steam turbine has length L = 50 mm and diameter D = 50 mm. It encounters a
In a particular application, the radial load acting on a ball bearing is 5 kN and the expected life for 90% of the hearings is 8000 Calculate the dynamic load carrying capacity of the bearing, when the shaft rotates at 1450 rpm.
A shaft rotating at constant speed is subjected to variable load. The bearings supporting the shaftare subjected to stationary equivalent radial load of 3 kN for 10 per cent of time, 2 kN for 20 percent of time, 1 kN for 30 per cent of time and no load for remaining time of cycle. If the total lifeexpected for the bearing is 20 × 106revolutions at 95 per cent reliability, calculate dynamic loadrating of the ball bearing.
An 02-series ball bearing is to be selected to carry a radial load of 8 kN and a thrust load of 4 kN. The desired life Lp is to be 5000 h with an inner-ring rotation rate of 900 rev/min. What is the basic load rating that should be used in selecting a bearing for a reliability goal of 0.90? Hints: Rating life is 1(10°) revolutions, Weibull parameters of rating lives are x, = 0.02,0 = 4.459, b = 1.483 respectively.
An 02-series ball bearing is to be selected to carry a radial load of 8 kN and a thrust load of4 kN. The desired life LD is to be 5000 h with an inner-ring rotation rate of 900 rev/min. Whatis the basic load rating that should be used in selecting a bearing for a reliability goal of 0.90?