Problem (7.1): An element in plane stress from the frame of a racing car is oriented known angle 6 (see Figure 7.30). On this inclined element, the normal and shear have the magnitudes and directions shown in the figure. Determine the normal and she stresses acting on an element whose sides are parallel to the xy axes; that is, determine Oy, and Txy. Show the results on a sketch of an element oriented at 0 =0°. at stresses 4,180 psi 2,360 psi 0=30° 15,220 psi Figure (7.30)

Problem (7.1): An element in plane stress from the frame of a racing car is oriented known angle 6 (see Figure 7.30). On this inclined element, the normal and shear have the magnitudes and directions shown in the figure. Determine the normal and she stresses acting on an element whose sides are parallel to the xy axes; that is, determine Oy, and Txy. Show the results on a sketch of an element oriented at 0 =0°. at stresses 4,180 psi 2,360 psi 0=30° 15,220 psi Figure (7.30)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a beam made from a material having an allowable tensile stress of 135 MPa and a compressive stress of 165 MPa. The couple M is applied to the beam in a plane forming an angle of 45° as shown in the figure. a) Determine the location of the centroid of the cross section b) Calculate the moments of inertia about the principal axes, I, and ly c) Determine the maximum allowable internal moment M that can be applied to the beam N M Y 140 mm 140 mm 45⁰ 140 mm 280 mm 140 mm 140 mm
Question 1 Find the state of of stress for the element in Figure Q1 inclined by 30° counter clockwise by using: a) Equation Method b) Mohr's Circle Method 60 MPa Txy = 20 MPa 90 MPa Figure Q1
The biaxial stress system in an element is shown in the figure. Which of the following will give the normal stress in N/mm² in the plane BD making an angle of 45° with the plane BA? σ¸ = 40 N/mm² G₁ = 60 N/mm 111 = 40 N/mm B a. = 60 N/mm
85 In a pure shear condition, the maximum value of shear stress is observed to be 20 MPa for an element shown, subjected to above condition. The change in length of diagonal AB is μm. [Take G = 80 GPa] [Correct upto 2 decimal places] D 10 cm A 10 cm B () C
Question-3 An element in pure shear is subjected to stresses - 16 MPa, as shown in the figure. Using Mohr's circle, determine (a) the stresses acting on an element oriented at a counterclockwise angle 0 = 20 from the x axis and (b) the principal stresses. Show all results on sketches of properly oriented elements. 16 MPa
Part C - Counterclockwise Rotation of a Stress Element Figure 5 of 6 The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5) where the magnitudes of the stresses are |0z| = 13 ksi, Joy = 23 ksi, and |Tzy| = 12 ksi. Determine the state of stress on an element rotated 45° counterclockwise from the element shown. Express your answers, separated by commas, to three significant figures. • View Available Hint(s) Vol AEO I vec Or =, oy =, Tự'y = ksi, ksi, ksi Submit Pearson
Q2) B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in Figure Q2(b). Take: Z =1 Y = 0 i) Determine the stress created at points A, B, and C. ii) Sketch a three-dimensional view of the stress distribution acting over the cross section. Note that moments of inertia for the circular area can be determined by I= (ar' )/ 4. y A B. M = 4Y0 Nm 45° Radius = 0.5(2Z) mm Figure Q2(b)
The state of strain at the point has components of € = 300 (10-6), y = -260 (10-6), and Yay = 460 (10–6). Figure
Q1: The state of stress at a point in a member is shown on the element in Figure (1). Determine the following: 1) The stress components acting on the inclined plane AB (o, and tx'y'). 2) The principal normal stresses (p1.op2) and max in-plane shear stress (Tmax). Do not calculate the angles of the planes of the principal stresses. Solve the problem using the equations. 8 ksi 2 ksi Figure (1) 60 B 5 ksi
tate of Stress Caused by Combined Loadings Learning Goal: To use the superposition principle to find the state of stress on a beam under multiple loadings. The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. 100 mm 15 mm 20 mm 200 mm 150 mm f 20 mm The dimensions are di - 2.15 m. d₂ = 0.5 m. -0.85 m d-285 mm and r= 150 mm The applied force has magnitude P=4.5 kN Part A-Support Reactions and Internal Loading C₁, C₂=₁ N=, V = ₁ M = Determine the support reactions C, and C, and the internal normal force, shear force, and moment on the cross-section containing point A. Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) Submit Part B- Properties of the Cross-Section A= I= Q = Submit VAX IT VOC JA=.TA= What are the cross-sectional area, moment of inertia with respect to the neutral axis, and first moment of the area with respect to point A for the…
3. The plane stress is shown on the element. Use Mohr's circle. 1) Determine the principal stresses and corresponding orientation of the element from the position shown. 2) Determine the in-plane maximum shear stress and corresponding orientation of the element from the position shown. 3) Determine the state of stress on an element oriented 45° counterclockwise from the position shown. 90 MPа 60 MPа 20 MPа
An element in pure shear is subjected to stresses Tzy = 3,650 psi, as shown in the figure. Consider only the in-plane stresses (the stresses in the xy plane). Try Using Mohr's circle, determine: (a) The stresses acting on an element oriented at a slope of 3 on 4 (see the figure) (Round your answers to nearest whole). psi psi psi O21 = Txlyl = Oyl = (b) The principal stresses. (Round your answers to nearest whole) Op1 = psi O22 =| o2 = psi