Problem 9-17: Determine the equivalent state of stress on an element at the same point which represents (a) the principal stress, and (b) the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine the corresponding orientation of the element with respect to the element shown and sketch the results on the element. 75 MPa 125 MPa 50 MPa

Problem 9-17: Determine the equivalent state of stress on an element at the same point which represents (a) the principal stress, and (b) the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine the corresponding orientation of the element with respect to the element shown and sketch the results on the element. 75 MPa 125 MPa 50 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
(a) Construct Mohr's circle for an element in a uniaxial state of stress (b) Use this Mohr's circle to derive the equation for the normal stress On and shear stress En on the n-face. The equations should depend on Ox and θ (c) Use the Mohr's circle to determine the planes on which the maximum shear stress acts. Sketch a properly oriented maximum-shear-stress element and indicate the normal and shear stresses acting on its faces. Ơn nt o, Note: for (b), the angle θ is between 0 and 90° and is positive
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of Sx = 210 MPa, Sxy = 150 MPa. Sxy Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane used in a mechanically stabilized earth wall. If the reference state of stress for this element results in the Mohr’s circle plot shown in Fig. E3-b, determine: The principal stresses. The principal directions (angles to the principal planes). The maximum in-plane shear stress. It is known that the seam, which is rotated 45 deg from the vertical as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated.
Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!
The rod has a diameter of 40 mm. (Figure 1) It is subjected to the force system F₂ = 1410 N, Fy = 635 N, F₂ - 820 N. Figure F F 300 mm 100 N-m F. 100 mm B 1 of 1 Determine the normal stress that acts at point B. Express your answer to three significant figures and include appropriate units. ов - Submit Part B (TB)zy μA Submit Value Request Answer Determine the shear stress Try that acts at point B. Express your answer to three significant figures and include appropriate units. BLA Value Request Answer Units ļ 20011 Units COOL ? HEIT
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, Px = 20 kN, P, = 16 kN, and P, = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a |P, y P: P H K
Problem 1: Given the 2D states of plane stress below, determine the principal stresses (0₁, 0₂) and the maximum shear stress (Tmax). Show your work. ox ºy Txy 90 MPa -30 MPa 15 MPa 90 MPa 180 MPa 60 MPa 0 MPa -40 MPa 120 MPa 01 02 03 Tmax
Problem 1: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 25 ksi, oy = 12 ksi, and Txy = 10 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 12 ksi 5 25 ksi 10 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the principal stresses, the maximum in-plane shear stress, and the normal stress that acts on the maximum shear stress plane. Label all of these quantities on the circle. (c) Calculate the orientation of the principal planes and the planes of maximum shear stress. Label all of these quantities on the circle. (d) Show all stresses from part (b) on properly oriented stress element(s). Be sure to include all stress components acting on the elements(s).
Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension. (a) Draw the Mohr's circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stress acting on a plane that is 30° from the major principal plane. kindly answer the following with a complete solution so that i can understand how to solve it. thank you
4 ksi The state of plane stress at a point is shown on the element. (a) Draw Mohr's circle neatly to scale, and use it to complete part (b). (b) Determine the state of stress on an element rotated 35° counterclock- 20 ksi wise from the given element. Sketch the state of stress on the rotated element element. 9 ksi -20 -10 o (ksi) -30 -20 -10 10 20 30 10 20 T (ksi)
To determine the normal and shear stresses on the indicated plane, we must first determine the orientation of the inclined plane relative to the x face of the stress element. Determine the magnitude of the counterclockwise angle between the x face and the inclined plane. Assume Sx = 170 MPa, Sy = 105 MPa, Sxy = 85 MPa, and ß = 65°. Sx Sxy В Sy Answer: 0 = 25 X O'