Q 3: A horizontal curve of a 4-lane undivided highway is built in acut sectionof side slope 3:1. If the design speed is 100kph, station of P.I=(55+00. Shoulderwidth = 1.5m, e=8%, q=1.5%, t=2.5sec, g=1.5% and A= 45°1. Determine the min. lane width that would allow a safe operaion on thiscurve?2. Draw the cross section at station (56+00) and at station (70+01)?

Answered: Image /qna-images/answer/991c4398-d3e6-443d-9ee4-c4f6dec2b8ce.jpg

Q 3: A horizontal curve of a 4-lane undivided highway is built in acut section of side slope 3:1. If the design speed is 100kph, station of P.I=(55+00. Shoulder width = 1.5m, e=8%, q=1.5%, t=2.5sec, g=1.5% and A= 45° %3D 1. Determine the min. lane width that would allow a safe operaion on this curve? 2. Draw the cross section at station (56+00) and at station (70+01)?

Q 3: A horizontal curve of a 4-lane undivided highway is built in acut section of side slope 3:1. If the design speed is 100kph, station of P.I=(55+00. Shoulder width = 1.5m, e=8%, q=1.5%, t=2.5sec, g=1.5% and A= 45° %3D 1. Determine the min. lane width that would allow a safe operaion on this curve? 2. Draw the cross section at station (56+00) and at station (70+01)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. On a divided highway with project speed of 90 kph, slopes of two red lines gi= %3,4 and g2= -%2,8, connect at an intersection point with 0+50000 km and elevation of 200,00 m. Please calculate: a. Length of vertical curve, b. Elevation at red line at points T1, T2 and every 15 m. (treact= 0,75sn, f=0,60).
5 Given: design speed = 100 kph, (f = 0.13), p = 0.4 m/sec3 , Sta. Pl = 5+ 000.000 Road width = 14.0 m (4-lane, 2-way), Normal crown = 1.5 %, Intersection angle = 30° Design the section of highway. I
An existing sag vertical curve on highway joins a +2.5% grade with a -5.1% grade. If the posted speed limit is 40 mph. Determine the length of the sag curve based on a. Stopping sight distance b. Comfort с. Арpearance
Design a Two way - one lane Highway with the following specification. V= 90 kph e=0.05 m=15 m SD=115 m wheel base = 2.25 m C=3 Pavement is rotated at center I =20 Determine the following: Minimum Radius Road Widening Transition Spiral (if any) Vertical Curve Tangent and Length of Curve Road Profile for horizontal alignment with station if the start station is 1+ 000
Why extra widening of road is required at horizontal curve?Determine the super-elevation in inch for a 60 feet wide road with a design speed of 70 mile/hr. and degree of curvature 8° ; ? = 0.155.
Given the proposed longitudinal profile of the centerline of a rural two-lane highway as follows: PVLu STN 10+0) PVL: Elev. 100 ft G-2% Ge0% L=? Ly=? a) Calculate the required minimum design lengths (to meet the SSD requirements) of the three back-to-back vertical curves on this section of the roadway to accommodate a continuous design speed of 50 mph.
C. Design a Two way - one lane Highway with the following specification. V - 90 kph e - 0.05 m. 15 m SD - 115 m wheel base - 2.25 m c- 3 Pavement is rotated at center | - 20° Determine the following: Minimum Radius Road Widening Transition Spiral (if any) Vertical Curve Tangent and Length of Curve Road Profile for horizontal alignment with station if the start station is 1 • 000
Assignment 3: Vertical Curve Design Question 2 The reduced level at the intersection of a rising gradient of P % and a falling gradient of Q % on a proposed road is XX.XX m. Given that K value is KK. The throught chainage of the intersection point is YYYY.YY m and proposed vertical curve is to have equal tangent. As a civil engineering you are required to prepare the following vertical curve design calculations: a) The through chainage of the points of the vertical curve if the minimum required length is to be used (Lv) and the vertical curve setting out data at 20 metres interval. b) The chainage and reduced level of the highest point on the curve. c) Through chainage at highest point was located exactly under a bridge, if the RL of soffit is SS.SS m, calculate the headroom based on proposed vertical curve design.
The curved section of a highway in Southern California connects two tangents at station 20+75.00 at an angle A = 25°. The point of curvature is at station 16+50. a) Determine the radius of the existing curve. b) Determine the station of the point of tangency. . c) Does the radius of the given horizontal curve satisfy the minimum requirement based on AASHTO standards? Assume a design speed of 70 mph and emax = 10%. Support your answer.
Given highway design parameters below, solve the questions a) through f). A curved section of a 4-lane undivided highway (i.e., 2 lanes rotation) Design speed = 40 mph • Design max superelevation = 8% Lane width = 11 ft • 2.5% normal crown Central angle(l) = 38°, Degree of Curve = 7.82°, and Plsta = 292+52.4 a. Determine PC,ta b. Determine PTsta c. Calculate the length of full superelevation (BFS EFS) ENC: End of Normal Crown; LC: Level Crown; BFS: Begin of Full Superelevation; EFS: End of Full Superelevation
Transportation engineering Read the question carefully and give me solution according to the question. Thank you. A horizontal curve of 6-lane divided highway is built in cut section of side slope 2:1. If the design speed is 100 km/h, station of PI is 60+00, lane width=3.6 m, e = 8 %, t = 2.5 sec, g = 2 %, and Δ=45°. Determine the min shoulder width that would allow a safe operation on this curve.
IOT is the vertical distance between which of the following two curves? А. None of these options B. Recession curve and storage curve Recession curve and Advance curve D. Depletion curve and advance curve