Q-3 The frame shown in Fig. 3 is fixed at A, E and pinned at D. Analyse the frame for the given loading using the moment distribution method, and draw the shear force and bending moment diagrams. 4 kN/m te (ZED) C Fig.3

Q-3 The frame shown in Fig. 3 is fixed at A, E and pinned at D. Analyse the frame for the given loading using the moment distribution method, and draw the shear force and bending moment diagrams. 4 kN/m te (ZED) C Fig.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The tension member shown in Fig.3 is a PL 1/2 x 8 of A36 steel. The member is connected to a gusset…

A: Given data:- For grade A 36, FY=36 ksiFu=58 ksit=0.5 inw=8 in Dead load =95 kips Live load =9 kips

Q: Problem I. With the ongoing extension of Manila Skyway, a series of 250 mm diameter circular poles…

A: The given load acting on the pole and at the base cross section can be shown below The combined…

Q: Find the moment of inertia about xx axis

A: Given :

Q: The line of sight of a total station is out of adjustment by 10″.In prolonging a line by plunging…

A: Given:- out of adjustment by 10" To find:- angular error

Q: What is a 'misfire'? Explain how you should manage a misfire, if it occurs?

A: Misfire means the complete or partial failure of a blasting charge to explode as planned. The…

Q: Series pipe ABCD consists of 6100 m of 400-mm, 3050 m of 300-mm, and 1520 m of 200-mm (C=100). Find…

A: Q=0.061m3/sec

Q: A sprinkler system 18 m spacing along the main and 12 m along the laterals is used to irrigate crop…

Q: Give examples of the important role of length in everyday life.

A: Explanation- The base distance between two distinct focuses is estimated by the length, and it is an…

Q: (c) Liquid flows through an orifice in the bottom of a cylindrical tank at a velocity of 4m/s. If…

Q: Series pipe ABCD consists of 6100 m of 400-mm, 3050 m of 300-mm, and 1520 m of 200-mm (C=100). Find…

A: Pipe arrangement of 3 pipes are given, there length and diameter is mentioned. it has been asked in…

Q: 4.7 A concrete beam of rectangular cross section of 200 mm x 400 mm is prestressed with a force 400…

A: b = 200mm d = 400mm A = b×dA = 200×400 = 80000mm2P = 400kNe = 100mm It has been asked in the…

Q: Q-1: Determine the resultant force at pins A, B and C on the three member frame. 800 N С 200 N/m 2m…

A: length of member AC = 2sin 600= 2.31 m load on member AC = 200 x 2.31 =462 N horizontal component =…

Q: a) List four possible methods for shallow ground improvement. b) Use the hel 66 DU

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Draw the shear and moment diagram for the beam with the loads and supports. PLACE ALL YOUR PROCEDURE…

Q: A k Answers: (a) σ₁ = 01 (b) VD = i (c) P = i i L (1) B L₂ b (2) in. kips. с ksi, 0₂ = с i D P ksi.

Q: Which reclaimable material makes up the highest percentage by weight of currently economically…

A: Out of the above options the materials which can be easily recycled are metals and paper including…

Q: uniaxial tension test is Fy (MPa). Based on the stress state against failure if all stresses are inc

A: von mises theory is theory of plasticity ,general stress matrix is σ1 τ12 τ13…

Q: Compute the force in members FH, GH, and EK of the Fan Fink truss shown in Figure 1- 102. 200 lb 200…

Q: 18. Find the gauge readings at A and B in Fig. 2.51. [Ans. 17.39 kN/m² (vacuum), 12.61 kN/m²]…

A: I have solved your problem below

Q: Question 1 * Each member of the truss shown is made of steel and has the cross-sectional area shown.…

Q: Structural panel/Sheets Explain ?

A: Structural Panel : Structural panels are lightweight, flat composite materials that can withstand…

Q: Series pipe ABCD consists of 6100 m of 400-mm, 3050 m of 300-mm, and 1520 m of 200-mm (C=100). Find…

Q: Describe how a total station can be leveled when the leveling bubble is out of adjustment.

A: In mine surveying, total stations are the most used survey device. As the drifts of an underground…

Q: [Ans. 17.39 kN/m² (vacuum), 12.61 kN/ -Closed A Mercury vapour Air K

A: PA= 80.04 KN PB= 111.44 KN

Q: Que. If the average sewage from a city is 95 × 1061/day and the average 5 day BOD is 300mg/l against…

Q: ...: The ladder in fig.(1), has a uniform weight of 100N and rests against the wall at B.If the…

Q: The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190…

Q: able having span of 100 m, dip total load of 25 kN/m. Find the c < 1016/0°C.

Q: One of the columns supporting the roof of a large building exerts a load of 1500kN on a circular…

A: The design of the footing is based on the criteria, qn ≤ qna where qn - Net pressure from the…

Q: (4) The cross section of a given column is shown in the figure, b.-24cm, x-2.02cm, the angle for the…

A: Solution: Design of lacing: Lacing provided at 45o to horizontal: Horizontal spacing = bo + 2xo =…

Q: Explain why the “principal of reversion” is important in angle measurement.

A: The term principle reversion is used in surveying field.

Q: During heavy rainstorms, sewer systems in some older cities can be overwhelmed with water. This can…

A: The various impacts of sewage being discharged into waterways are: Now a day’s there is an…

Q: A massless beam has a loading pattern as shown in the figure. The beam is of rectangular cross…

Q: A 20 KN weight is suspended by two wires as shown in the figure. The length of each wire is 2 meter.…

Q: Shown below is a trapezoidal area which will be excavated and used as borrow pit. It has been laid…

A: solution Elevation = 50 m we have to Determine the volume of excavation in cubic meters by using:1)…

Q: A fully loaded water-plane of a 420-m long supertanker has the following half-ordinates: 0.0, 8.9,…

A: This question is related to the Hydrology Engineering.

Q: What is the relationship of a forward and back azimuth?

Q: What error in horizontal angles is consistent with the following linear precisions?1>5000,…

A: 1 rad =206,248.8"(a) 15000×206,248.8"=41.25"(b) 120,000×206,248.8"=10.31"

Q: 2= The deformations of a body are presented as follows. Find the Cauchy strain tensor [Cij] and…

A: point (2,2,1) t*=2 α=1 So the deformations would become=…

Q: Determine the effective length factor for each of the columns of the frame shown in Fig. 7.4 if the…

A: The given figure is shown below:

Q: SI units) A bridge to be fabricated of steel girders is designed to be 500 m long and 12 m wide at…

A: Expansion joint Bridge expansion joints are made to extend the length of a bridge to accommodate…

Q: Four columns of a building are to be located within a plot size of 10 m x 10 m. The expected load on…

Q: (1) The out-plane stability formula of beam-columns recommended in the design code is as following:<…

A: Solution- These factors have the following values:-

Q: Why is it important to adopt a standard angle measuring procedure, such as always measuring angles…

A: It is important to adopt a standard angle measuring procedure,

Q: The continuous beam ABC, Fig 2, is hinged at A and roller supported at B and C. Selecting the…

A: I am uploading the solution for opposite case with length L and using as w.please interchange the…

Q: A canal is excavated to a depth of 4 m below ground level in a soil having C = 15 kN/m², 3 = 18°,…

Q: 4.7 A concrete beam of rectangular cross section of 200 mm x 400 mm is prestressed with a force 400…

Q: A catchment has an area of 150 hectares and a run-off/rainfall ratio of 0.40. if due to 10 cm…

Q: A 5m tall CLT Wall (Grade V1) is subjected to a dead load of 200 kN/m and a live load of 300 kN/m.…

A: Total axial load P = 200 + 300 = 500 KN For Grade IV acceptable thickness of CLT wall = 567 mm…

Q: B find the max Value of (P) that can be applied on the Cantilever beam Shown in figure, knowing that…

A: Consider the given beam. Calculate the moment in the beam as follows. M=Pcosθ×450=P×35×450=270P N·mm

Question

Q-3
The frame shown in Fig.3 is fixed at A, E and pinned at D. Analyse the frame for the
given loading using the moment distribution method, and draw the shear force and
bending moment diagrams.
WA
200
4 kN/m
(2ED)
(ZET)
201
Fir.3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q-3 The frame shown in Fig.3 is pinned at A and fixed at D, with a roller support at B. Analyse the frame for the given loading using the slope-deflection method, and draw the shear force and bending moment diagrams.(constant EI). 80 KN 5m 5m B 30 kN/m 10m 10m OF=161-1 OC - 97.2 Fig.3
THE OVERHANGING BEAM IN THE FIGURE CARRIES A TRIANGULAR LOADING, THE INTENSITY OF WHICH VARIES FROM O TO 10 KN/M, AN UNKNOWN CONCENTRATED LOADING P, AND AN UNKNOWN UNIFORMLY DISTRIBUTED LOADING W. KNOWING THAT IT HAS BEEN EXPERIMENTALLY DETERMINED THAT THE BENDING MOMENT IS +128/9 KN-M AT C AND +172/9 KN-M AT D. (A) DETERMINE THE VALUES OF P (IN KN) ANDW (IN KN/M), (B) DRAW THE SHEAR AND BENDING-MOMENT DIAGRAMS. (c) DETERMINE THE LOCATION OF ZERO SHEAR FROM POINT A AND THE MAGNITUDE OF MAXIMUM MOMENT. NEGLECT THE WEIGHT OF THE BEAM. HINT: THE LOCATION OF ZERO SHEAR IS ALSO WHERE M-MAX OCCURS. P 10 kN/m W C E A 2 m 2 m 2 m 2 m
Consider the loaded frame in Fig Q3. Use the Principle of Virtual Work to evaluate the following: a. The horizontal support reaction at point A. b. The bending moment at point D. Indicate clearly which way this moment is curving member BC at this point. |10 kN 1.5 m A В 15 kN D 3.0 m 2.0 m 12 kNm) 3.0 m
The frame shown in Fig.2 is fixed at A and D. i-Analyse the frame using the slope deflection method. ii- Verify the results in "i" above using the moment distribution method. iii-Draw the shear force and bending moment diagrams for the frame. 2 kN/m (2E) B (2E1) (EI) D 2m 2 m 2 m
2. Determine the reaction at each support and draw the shear and bending moment diagram of the beam shown. Use moment distribution method. 226kN 63.5kN 226kN E ↓ cftt A B D m m 2m m 4 m 4m 21 E = constant G
4:35 Back Final Exam_ CIVL3036_SP2... 7 of 7 Q6: Using the moment distribution method, determine the internal moments and the support reactions and draw the bending moment diagram for the beam shown below. Assume El is constant. 150 kN 150 kN 50 kN/m El Constant 2 m + 2 m + 2 m
8. The U-frame ABCD shown in Fig. 8 is simply supported at B and C. Evaluate the load W so that the horizontal displacements at A and D are zero. Also evaluate the vertical displacement at the midspan of BC and the rotation of joint B. A D W El constant throughout linearly distributed loads 2a uniformly distributed load В C 00 2a PLEASE VERIFY YOUR ANSWERS 8. W - 3qa/5 : Удс —- 7qa* /120EI ; Ө, —- qа* /30EI
w - We sin PROBLEM 5.52 Determine (a) the equations of the shear and bending-moment curves for the beam and loading shown, (b) the maximum absolute value of the bending moment in the beam.
Problem 3. Draw the shear and Bending Moment Diagram of the beam shown. Solve the problem using Moment Distribution Method A P/2 a/2 L2 P a W 39.5kN/m B P 118.50KN W L1 a 3.60m - → L1 7.10m L2 6.10m
PROBLEM 2.29 The guy wire BD exerts on the telephone pole AC a force P directed along BD. Knowing that P must have a 720-N component perpendicular to the pole AC, determine (a) the magnitude of the force P, (b) its component along line AC. 7 m 2.4 m
Force P with 5.05 kN magnitude acts along the parallelepipeds diagonal CE, pointing towards E 290 mm 290 mm 145 mm Determine the magnitude of the moment of Pabout the following Ines in N-m. (a) Ine OA N-m (b) ine O8 N- m (c) Ine AB N-m (d) Ine BF N-m (e) ine BG N-m (r) Ine DG N-m (a) Ine 0D N-m (h) Ine OC N-m (1) ine EF N-m (1) Ine OF
against a smooth support at B. Determine the horizontal and vertical 6 kN EXAMPLE The member shown in Fig. is pin connected at A and rests components of reaction at the pin A. 80 N/m Ans. 30 NB-200 N 90 N m Ax 100N 0.75 m 1.5 m Ay 233 N