Q₁: A sequential network has one input and one output. The output becomes 1 when either 010 or 00 is detected in its input. Otherwise, it gives 0 in its output. a. Draw a diagram (use mealy model with minimum number of states (not more than 3 states). b. Construct a state table. c. Using D flip-flops, construct a state assigned table. d. Determine the next-state and output logic expressions. e. Sketch the corresponding logic circuit.

Q₁: A sequential network has one input and one output. The output becomes 1 when either 010 or 00 is detected in its input. Otherwise, it gives 0 in its output. a. Draw a diagram (use mealy model with minimum number of states (not more than 3 states). b. Construct a state table. c. Using D flip-flops, construct a state assigned table. d. Determine the next-state and output logic expressions. e. Sketch the corresponding logic circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Q1. Determine the output waveform and Boolean expression X of the logic circuit in given circuit. D. B Q 2. Find the all Boolean expression for Y1, Y2, Y3, and Y4 (in the Q-1) and the intermediate waveforms at each of points Y1, Y2, Y3, and Y4.
You want to design a synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and will not count the decimal digits in the last two digits of your student number. a. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. b. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last two numbers 02
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?
A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are attached below: a) Draw the logic diagram of the circuit. b) Derive the state equations for A and B c) Tabulate the state table. d) Draw the state diagram for the circuit and describe the function of circuit.
Design a combinational circuit with four input lines that represent a decimal digit in BCD and four output lines that generate the 9's complement of the input digit. Provide a fifth output that detects an error in the input BCD number. This output should be equal to logic 1 when the four inputs have one of the unused combinations of the BCD code. Provide a schematic logic diagram of it. It will surely help me in my review. Thank you so much!
(a) Construct the state table and determine the state equation of this circuit. (b) Consider the following three different approaches of implementing the sequential logic circuit Sketch the logic diagram of the circuit for each case (i) Use a negative-edge triggered D flip-flop and some primitive gates (i) Use a positive-edge triggered JK flip-flop and some primitive gates (ii) Use a positive-edge triggered T flip-flop and a 4x1 multiplexer
Draw the equivalent logic circuit diagram of the following expressions : a. XY = F b. X + Y = F XÝZ = F c. d. XY + XZ = F e. XYZ + XÝZ = F
(c) Figure Q5(c) shows a logic circuit which has three inputs A, B, C and two outputs F and G. i) Obtain the logic expression for the outputs G and F. ii) Redesign the circuit using only 3-to-8 decoder (with active high outputs) and OR gates. G A B F Figure Q5(c)
A B Prepare the truth table of the logic circuit (logic circuit) on the right. Then, using the truth table, write the function you have obtained according to the SOP (minterm) without any simplification and draw the logic circuit for the new function you have obtained. Make sure that the circuit you have drawn is understandable, the function you have written and the truth table are readable.
a) For the given logic circuit diagram write the program by using the gate level modeling. b) For the given truth table write the program by using the data flow Modelling. c) Write the test bench of the given logic circuit with all possibilities Y1 Y2 Y3 Y4 Y5 Y6 Y7 A2 A1 A0
4. Figure 2 shows a logic circuit with output F Figure 2. Logic circuit with gate I (AND), gate II (AND), gate III (NOT), gate IV (AND), gate V (EXOR) and gate VI (OR) a. Find the Boolean expression of output F. b. The simplified Boolean expression of Output F. c. If the input A and C were High and Input B was Low, what is output F: