Q1: A certain point in the mechanical part shown in Figure below. Use Mol determine: (a) the magnitude and nature of the principal stresses and the inclinations of the principal planes. (b) the maximum shear stress and the inclinations of the planes on which it acts. (c) the magnitude of the normal stress and shear on a plane inclined at 25° counterclockwise to plane on which the 60 MN/m² stress acts. 50 MN/m² 30 MN/m²

Q1: A certain point in the mechanical part shown in Figure below. Use Mol determine: (a) the magnitude and nature of the principal stresses and the inclinations of the principal planes. (b) the maximum shear stress and the inclinations of the planes on which it acts. (c) the magnitude of the normal stress and shear on a plane inclined at 25° counterclockwise to plane on which the 60 MN/m² stress acts. 50 MN/m² 30 MN/m²

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
The stresses acting on element A on the web of a train rail (sec figure part a) a re found to be 6500 psi tension in the horizontal direction and 18,500 psi compression in the vertical direction (see figure part b), Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an clement oriented at a counterclockwise angle of 30° from the horizontal Show these stresses on a sketch of an element oriented at this angle
Through 7.4-25 An clement in plane stress is subjected to stresses x,y, and r. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.422x=29.5,y=29.5MPa,xy=27MPa
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.