Q1) It is desirable to use the 32-in pump of Figure below at 1170 r/min to pump water at 60°F from one reservoir to another 120 ft higher through pipe 1500 ft long and 16 inch ID with friction factor f= 0.00725. (a) What will the operating point and efficiency be? (b) To what speed should the pump be changed to operate at the BEP?

Q1) It is desirable to use the 32-in pump of Figure below at 1170 r/min to pump water at 60°F from one reservoir to another 120 ft higher through pipe 1500 ft long and 16 inch ID with friction factor f= 0.00725. (a) What will the operating point and efficiency be? (b) To what speed should the pump be changed to operate at the BEP?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Theoretical Torque required, TT (N-m). (Hint: first calculate the mechanical efficiency and theoretical flow rate. Convert rpm to rad/s). O 9.41 N-m 8.85 N-m 9.35 N-m 9.62 N-m 8.80 N-m
Q1/ liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to 45° elbow 8 m Fig. (1) Globe valve Tank 5 m supply water to the tank at the rate of 245 I/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the pump required 12 m NPSH is it suitable to prevent cavitation for this system? why? Given that: u = 0.0016 Pa.s; p 850 kg/m', e/d 0.0035, (Le/d) of Globe valve (open) = 240 (Le/d) of 45° ēlbow = 24 and Pv = 36.6 kPa 25 m 45° Reservoir 45° elbow
Please include a diagram.A pump supplies water at a flow rate of 4ft3/s from an open reservoir through a horizontal 8-in sched 40 pipe. The head loss from the reservoir to the suction of the pump is 2 ft-lbf/lbm, and the discharge is at 90 psig into a 6-in sched 80 pipe. The pump has an efficiency of 65% answer the following:a.) The head that must be delivered by the pump to the water is ________ or energy developed by the pump or output energy of the pumpb.) input energy to the pumpc.) Rated power of the pump in kW
Q3: Two tank are connected with piping system as shown. If the pump characteristics are given by: hp- 31-120000 and, 7p--190000Q+8590Q Where hp is in meters and Q in m³/s and np is the pump efficiency (%).Estimate the operational cost of the pumping (10000) m² of water to the upper tank if the cost of IKwh is 2000 ID. Neglecting the minor losses. H=15mm 0-150mm
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a. 100 kPa b. 225 kPa c. 150 kPa d. 75 kPA
Pump at its best efficiency point(BEP) has a capacity of 12500 gpm while developing a head of 60ft at a rotative speed of 1450rpm. What is the specific speed of the pump? ANSWER: 7520rpm
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Actual Torque Required, TÀ (N- m). (Hint: first calculate the mechanical efficiency and theoretical flow rate. Convert rpm to rad/s). O 10.6 N-m O 9.94 N-m O 8.01 N-m O 9.35 N-m O 8.85 N-m
A Pelton wheel develops 70 kW under a head of 60 m of water. It rotates 400 rpm. Overall efficiency is 80%. Find the discharge rate in m³/s. Use the equation below, where P is power of the turbine shaft and no is the overall efficiency, where specific weight of water is is 9.80 kN/m³ no P YQH A generator is driven by a small, single-jet Pelton turbine designed to have a power specific speed sp 0.20. The effective head at nozzle inlet is 200 m and the nozzle velocity coefficient is 0.985. The runner rotates at 880 rev/min, The turbine overall efficiency is 80%. Find (a) the power delivered by the shaft of the turbine and (b) find the power delivered by the water to the turbine. where density of water is 1000 kg/m³ and g is 9.80 m/s². Use Stup Ω P/p (gHE)* Overall efficiency ne and Power developed at turbine shaft hydraulic power P YQH
A pump with a 25 cmrev and 1000 rpm supplies the following circuit. If the characteristios of the Sokg cylinder are v-0.1 ms, piston diameter60mm, rod diameter-25mm and friction factoe-2000 Ns/m and the characteristics of the 100kg cylinder are v0.02 m/s, piston diamcter-40mum, rod diameter-30mm and friction factor-s00 Nsim. Determine the flow rate and pressiare on cach cylinder. 25cm 100 kg lo aorem Boky v.0.1 Piston 6e
What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with pressure of145 ft head?
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discharge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023. Include the diagram in your solution. a.100 kPa b.150 kPa c.75 kPA d.225 kPa