Q1. Differentiate: - • FPGA and CPLD • Edge trigger and Level Trigger • Octet and Quad
Q: Discussion: 1- Design decade counter using D flip flops.
A: As Per policy ,I can answer any one question So I am solving first question . Clock count QD QC…
Q: ) Design a state diagram for the monitoring unit. Your design should include three edge triggered…
A:
Q: Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The…
A:
Q: CIr CIk Next Output State FFs Dec Dec
A: To design a binary counter that counts from 0 to 5, we require three JK flip-flops. The clock of…
Q: How many flip-flops will be needed when following synthesized? codes ar always @(posedge clk) begin…
A: A flip flop is used to store 1 bit of information to store series of data registers are used. Always…
Q: 1. Design a 3-bit ripple counter using JK flip-flop. State Table: 3-bit ripple counter Present State…
A: Ripple counter: It is type of the asynchronous counter. The circuit is ripples when the clock pulse…
Q: For the circuit below X=1,B=1,Y=1,C=1. What will be the next state for the flip-flop? A. set B.…
A: Given: X=1, B=1, Y=1, C=1. The truth table for J-K flip flop is J K Q(n+1) 0 0 Q(n): Previous…
Q: 2- Design synchronous counter using positive edge J-K flip flop to count the following states…
A:
Q: 9 Using D flip-flops, (a) Design a counter with the following repeated binary sequence: 0, 1, 2, 4,…
A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…
Q: B A OUT AR of-4 0 tiplexer TPL Tristate CLK P Flip-flop output buffer S, =0 So =o clock SP OE LA 320
A:
Q: Qi: Design a synchronous binary counter using D flip- flop with the sequence shown in the state…
A: In synchronous binary counters clock input clocked together at same time with the same clock input…
Q: 5. The waveform in Figure Q5 are applied to the inputs of a J-K flip-flops (negative-edge…
A:
Q: 2. The asynchronous circuit shown in Figure 1 consists of two D flip-flops and a NAND gate.Complete…
A: D- Flipflop: Q(n+1)= D
Q: 1. Analysis with D Flip- flop. Example : Consider the following equahion Cinput eauation for D…
A: The Boolean expression of D flip-flop is given below: (a) Sequential circuit is shown below:…
Q: In/Out 1/0 00 01 1/0 0/0 0/0 0/0 11 1/1 10 1/1
A: Sequential circuits
Q: Q1. a) Given the State Diagram of Figure 1, draw and complete the state, transition, and output…
A: According to the question, for the given state table as shown below We need to design the state,…
Q: PROCEDURE Draw the circuit diagram of a decade counter using negative edge-triggered flip-flops. The…
A: The truth table for the JK flip-flop is given as: From the above table, It is seen that the output…
Q: 5-For the circuit shown, draw the timing diagram and its truth table, assume initially zero for each…
A:
Q: Q5(a) Design a synchronous counter using JK flip-flop to obtain the following count sequence: 1, 4,…
A: A counter is a sequential circuit whose state represents the number of clock pulses fed to the…
Q: What diagram shows the correct timing of a negative-edge-triggered T flip-flop? Annotate some…
A: The output of the T flipflop will not change or be retained if the input to the flipflop is 0. If…
Q: What is the type of the flip flop? Present state Next state output output At delay cross coupled D…
A: Based on the digital circuit
Q: (a) Provide a block diagram and a function table for the D-type flip-flop with falling edge…
A: Since you have posted multiple questions, we will solve the first question for you. If you require…
Q: Draw a ripple decade counter using negative edge-triggered JK flip- flops and draw the timing…
A:
Q: Q4/ (Answer One Only) from the following : 1- Design synchronous counter using negative edge D- type…
A:
Q: 4. Use a JK flip-flop and logics to implement the following. x:T2: F+ z y T1: F +/F J >F
A:
Q: For a 5421 code up counter designed using JK flip-flops, which of the following statements is false?…
A: BCD CODE-binary code in decimal represent than consider it as don't care. Also if any invalid BCD…
Q: 3 Consider a T flip-flop constructed from the negative edge triggered JK flip-flop with active low…
A: The solution is given below
Q: 1. Design a synchronous counter of three input (q1, q2, q3) using negative edge triggered T flip…
A:
Q: 1) Construct a JK flip-flop using a D Flip-flop, a 2-to-1 line multiplexer and an inverter. I need…
A:
Q: Design a sequential circuit with input M and output A using the given state diagram. Reduce the…
A: As per our guidelines we are supposed to answer only first 3 subparts. Kindly repost the other parts…
Q: Discussion 1. For a master-slave J K Flip - Flop with the inputs below, sketch the Q output…
A:
Q: Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The…
A:
Q: DESIGN 1-6 SYNCHRONOUS UP COUNTER USING JK FLIP-FLOP 7476 IC REQUIRED: A) EXCITATION TABLE OF JK F-F…
A: The solution is given below
Q: Construct JK flip-flop circuit diagram using D flip-flop and explain the characteristic table.
A:
Q: Write verilog code for d flip flop with its testbench code.
A: Latch is asynchronous device. It is level triggered device. It check input and change output…
Q: Illustrate a complete timing diagram (i.e., one entire cycle back to the starting states) for a 4…
A: 4-bit ripple counter using T flip-flops with negative edge clock triggers:
Q: Flip-flops Give the disadvantages and advantages of Positive Edge Triggering vs Negative Edge…
A: According to the question, Flip-flops Give the disadvantages and advantages of Positive Edge…
Q: 1. Construct the SR Flip Flop circuit shown in Figure 5.1. PRE iIs equal to SET and CLR is equal to…
A: From the above question the diagram is shown below:
Q: What is the type of the flip flop? gated T Flip Flop gated JK Flip Flop gated SR Flip Flop O Gated D…
A: Choose the correct option What is the type of the flip flop in the shown figure.
Q: Discussion: 1- Design decade counter using D flip flops. 2- Design mod 5 counter using SR flip flop.
A:
Q: Complete the design for the state machine described in the state diagram below and Write out the…
A: I have explained in detail
Q: D THE (a) Logic diagram QDQ(+1) 000 011 100 111 (b) Characteristic table 0
A: Logic gates are divided into seven part . This gate is used in digital electronic, it is based on a…
Q: Q Write a verilog code for positive edge triggered D-flip flop with. asynchronous reset.
A: A flip flop is used to store 1 bit of information to store series of data registers are used. D flip…
Q: The state diagram shown: 1. Write the characteristic equations 2. Design use T Flip Flops Draw ASM…
A: Given: Let input be X Y Let be output be A Z
Q: Create an Asynchronous Modulus 12 counter (sequence from 0000 through 1011) using negative-edge…
A:
Q: Design synchronous counters that go through each of the following sequences f. 1 3 5 7 6 4 2 0 and…
A: A synchronized counter is one in which all of the flip flops are timed at the same time using the…
Q: The following serial data stream is to be generated using a J – K positive edge – triggered Flip –…
A:
Q1. Differentiate: -
• FPGA and CPLD
• Edge trigger and Level Trigger
• Octet and Quad
• Synchronous and Asynchronous sequential circuits
• D-Flip Flop and T-Flip Flop
Step by step
Solved in 4 steps
- c) d) Explain the different between sequential circuit and combinational circuit. Identify input conditions necessary in order to set, reset and toggle the JK flip flops in Figure Q3d(i) and Q3d(ii). Clock- K Q 10 Figure Q3d(i) Clock K Q 10 ā Figure Q3d(ii)answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
- Electrical Engineering A Explain Digital IC specification using a neat diagram. B Design a circuit using AOI logic which outputs a 1 when a 4-bit BCD code translated to a number that uses the lower right segment of a 7-segement display. 0828956389 C Design a synchronous counter using D flip flops that counts 2, 3, 5, 7, 10, 12, 14 The unused states of the counter change to 6 at the next clock pulse. An asynchronous sequential eirenit ie dasasi5. JK flip-flops are often used to build counters. The JK flip-flop will toggle the original output value when triggered by the clock signal if both the J,K inputs are connected with a constant "high"(logic 1). All the JK flip-flops in Figure 2 are negative edge triggered. All the initial values of Q2Q1Q0 are 0. Qo (LSB) (MSB) Input K K Logic 1 Input Q2 000 Figure 2. Counter (a) Sketch the output waveforms forQ2 Q1 Q0. Write down the output binary value (Q2Q1Q0: such as "000", "001") for each clock period on the figure. (b) Describe the function of the counter (e.g. binary down counter counting from 7 to 0).Analyze the state machine in the figure below. Write i) Flip-flop input and output equations; ii) transition/output table; iii) state/output table (use state names SO, S1, S2, S3 for Q1Q0=00, 01, 10, 11); and iv) draw the corresponding state diagram. CLK- DO QO 0 CLK D1 Q1 1 CLK Z
- Design a Up Down Counter by using JK flip flop and verify the output of your designed circuit onany random input. Provide the following information as well:1. State table2. State diagram3. State equations4. Complete circuit diagramThe waveforms in Figure 08 are applied to the 4-bit parity logic. Determine the output wave-form in proper relation to the inputs. For how many bit times does even parity occur, and how is it indicated? The timing diagram includes eight bit times. Q.21 Bit time Ao A1 A2 A3 FIGURE 08Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
- Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).theirs clear deferent between linear reference and sawtooth more harmonics less harmonics the inverter always produce trapezoidal signals pure sine wave signals 6 active sectors with 2 zero vectors SVPWM have 6 sectors O