Q2: A distributor (d.c ring distributor) of ABCDA is fed from point A with 250 v and has a resistance of 0.42 per 1 km. The distributor supplies loads of 150 Am at point B, 300 Am at point C and 250 Am at point D. Determine the distance of each side of the ring, and determine the voltage at each load point. AB side = 1.111 of BC, AB side = 0.8 of CD, and AB side - DA The current flow between AB is 336.75 Am The voltage at point B is 243.265 v

Q2: A distributor (d.c ring distributor) of ABCDA is fed from point A with 250 v and has a resistance of 0.42 per 1 km. The distributor supplies loads of 150 Am at point B, 300 Am at point C and 250 Am at point D. Determine the distance of each side of the ring, and determine the voltage at each load point. AB side = 1.111 of BC, AB side = 0.8 of CD, and AB side - DA The current flow between AB is 336.75 Am The voltage at point B is 243.265 v

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
W1 A 1 IL Tr1 AC Supply V V w2 12 Tr2 use double range voltmeter Fig.(1)
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
the non-inductive resistance of kelvin double bridge are set at 100ON each, the standard resistance is set at 0.10020 and the low resistance 0.0000122 was very low. determine the unknown resistance
Six 100Wp crystalline PV modules, each with an open circuit voltage (Voc) of 30V, are connected in series in a string. What would be the total open circuit voltage (Voc) of the string of modules? And what would be the total Wp of the string? 180V, 600Wp 180V, 100Wp 30V, 600Wp 30V, 100Wp The distance from a combiner box to a PV array junction box is 4 m. The voltage drop of the used cable on this distance is 0.5 V. The current is 8.0 A. What is the power loss on this distance? 16 W 32 A 4 W 2 W A PV system has a rated capacity of 10 kWp. The overall efficiency of this PV system is 75% . The average daily irradiance at the site is 4 kWh/m²/day. What is the expected average daily energy output of this system? 3 kWh 30 kWh 7.5 kWh 40 kWh
Determine the DC currents (IB, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) Ig=Blank 1 mA, Ic=Blank 2 mA, IĘ=Blank 3 mA, VBE= Blank 4 V, VCE = Blank 5 V and VCB = Blank 6 V Use 2 decimal places. Use the following values: VBB = 2V RB = 7 kQ Rc = 248 Q Vcc = 19 V BDc = 56 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer Blank 6 Add your answer
Determine the branch currents Is, Igandl, in ampere. TVⒸ so www 14 Eng al. The current in ampere 11 [Select] b). The current in ampere 12 [Select] 60 www d. The current in ampere 13 [Select] 40
Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V la
Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
Q3: Using DIY trausformantion, Determine 4he Current (1) through the galuano meter in wheatstone Biralge 2002 in 8V
A 2 wire d.c. ring distributor is fed at A with 220 V. The various loads are 10A at B, 20A at C,30A at D and 10A at E. The resistances of the sections AB, BC, DC, DE and EA are 0.1 £2, 0.05 $2, 0.01 2, 0.025 2 and 0.075 respectively. Determine, a. Point of minimum potential b. Current in each section [Ans.: Point C, 29.04 A, 19.04 A, 0.96 A, 30.96 A and 40.96 A
In the circuit in Figure 2, the capacitor andThe circuit of resistance is defined as a load circuit.a) Find the average power dissipated by the load circuit?b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Interpreting the results obtained?c) In the circuit in Figure 2, with a resistance of 80 ohms 23?A coil of is connected in series. In this case,calculating transformer ratio () to optimize power delivery to the load? Obtainedinterpreting the result?d) Calculate the distributed load complex power and reactive power in the newly learned circuit?