Q2) A radar receiver with a 50 2 input resistanceoperates at a temperature of 29°C. The received signalfrequency, bandwidth and signal voltage shown in tablealso it is applied to an amplifier with a noise figure(NF) shown in the same table. Calculate the following:i) The input noise power, PN.ii)Theinputsignalpower,Ps.iii)SignaltoNoiseRatioindecibels,SNR.iv)ThenoisefactorFandSNRof theamplifier.v)Thenoisetemperatureoftheamplifier.(Given Boltzmann constant, k = 1.38x1023)Student name signal frequencybandwidth signal voltage|noise figure (NF)LAKSHMI8047µV2.5 dBLJINA6016|6µV2.4 dBMAZOUN90158uV2.6 dBMOHAMMED 7065 μν2.3 dB

Since you have asked multiple subparts with multiple samples. we will solve all subparts for the…

Q2) A radar receiver with a 50 Q input resistance operates at a temperature of 29°C. The received signal frequency, bandwidth and signal voltage shown in table also it is applied to an amplifier with a noise figure (NF) shown in the same table. Calculate the following: i) The input noise power, PN.

Q2) A radar receiver with a 50 Q input resistance operates at a temperature of 29°C. The received signal frequency, bandwidth and signal voltage shown in table also it is applied to an amplifier with a noise figure (NF) shown in the same table. Calculate the following: i) The input noise power, PN.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
One input to a conventional AM modulator is a 600 kHz carrier with amplitude of 22 V. The second input is a 20 kHz modulating signal that is of sufficient amplitude to cause a change in the output wave of +9 V. Determine: a. Upper and lower side frequencies. b. Percent modulation. c. Peak amplitude of the modulated carrier and the upper and lower side frequency voltages. d. Maximum and minimum amplitudes of the envelope. e. Expression for the modulated wave. Then, f. Draw the output spectrum. g. Sketch the output envelope.
The carrier frequency is 600 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. If the peak voltage level of modulating and 1v and signal respectively, determine the modulating index. the carrier are 2V 2 1.5 1 0.5 -0.5 -1 -1.5 -2 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
Discuss how the circuit produces a Frequency Modulated Signal
a) Consider the system shown in Figure 3(a). An input signal vm(t) is multiplied by a complex exponential signal e10nt The output signal v,(t) is fed into a low pass filter (LPF) with cut-off frequency wc. The input signal Vm(@) and the output signal V.(@) are as shown in Figure 3(b) and (c), respectively. i. Write the mathematical equation for signal in Figure 3(b). ii. Sketch signal, V,(@). iii. Based on the given V, (w), write the mathematical expression of the LPF, H(@) and state its cut off frequency, wc. iv. Sketch the output of LPF, V(@), if the cut off frequency of LPF is 10. v:(t) LPF Vm(t) vo(t) H(@) ej10nt (а) |Vm (@)| IV,(@)| 10 8 6. 3 -20715T-10T-5n 5n 10n 15n 20n -57 (b) Figure 3
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
in FM , the maximum allowable frequency deviation is 4kHz and the frequency deviation by noise is 156.42HZ? then the signal to noise ratio is .......
Q2. An angle modulated signal with a sinusoidal carrier 100 cos Znfat and a sinusoidal message with frequency fa-20 Hz, knowing that -0.7, a) Draw the single sided spectrum b) Determine the modulated signal bandwidth. c) Determine the 70% and 90% bandwidth and transınitted power.
Problem 1 The Figure below shows a screen shot of a signal recoded by an oscilloscope. a) What are the average and fundamental frequency for the given signal? b) If the signal is sampled with a sampling frequency of 10 Hz, sketch the sampled signal on the same chart. c) Find the average value of the sampled signal. d) Use zero-order hold to convert the sampled signal to a continuous one and sketch your result on the same chart 2. 0.5 0.4 Time (s) 0.1 0.2 0.3 0.6 0.7 0.8 0.9
1.3 We have a band pass signal in the frequency band, 450 Hz to 460 Hz. The carrier frequency is 455 Hz. We want to sample the signal. We have two choices: 1) Sample at more than twice the maximum frequency and 2) Sample at more than twice the bandwidth. Compare the two options of sampling the signal in terms of sampling frequency.
drive a formula for (SNR) of sinusoidal signal has been sampled and quantized.
7-22 Abasehand signal with frequency components from near de to 15 kHz frequency modulates a 200-kHz carrier, and the frequency deviation is +3 kHz. The signal is applied as the input to a cascade of two frequency triplers and one frequency doubler. Determine the output (a) center fre- quency, (b) frequency deviation, and (c) deviation ratio.