Answered: Q2: Calculate the depth H ofwater in…

Name: Q2: Calculate the depth H of water in Fig. below at which the conical
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2: Calculate the depth H of water in Fig. below at which the conical valve starts moving.Take the weight of the valve as 1962 N, and WN=7848NW-7848N1m1mF1.5m 1

Engineering

Mechanical Engineering

Q2: Calculate the depth H ofwater in Fig. below at which the conical valve starts moving. Take the weight of the valve as 1962 N, and W=7848N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
H-W 2 Q1/ Compute the horizontal and vertical components of the hydrostatic force on the quarter-circle panel at the bottom of the water tank in Fig. Water 2m
The pressure at point m in the figure shown was increased from kPa. This causes the top level of mercury to move 28 mm in the sloping tube. What is the inclination (angle ). Ans. 85 kPa to 125 34.932 0 X C water mercury
A door in the side of a tank is 20cm wide and 30cm high. If the tank is filled with oil r.d. 0.82 to the top of the door what is the force exerted on the door and the position of its line of action How much oil will have to be drained out for the force to be 40N and what will be the position of the new line of action
A triangular plate shown in the figure is submerged in oil, specific gravity = 0.8, 3.37 %3D m below the surface. The width and height of the plate is 1.52 m and 7.28 m, respectively. Find the location of the force from the bottom in millimeters. V FFS
Q1) The inverted U-tube manometer of Fig. contains oil (SG 0.9) and water as shown. Find The pressure differential between pipes A and B. If a =1.5 m , h= 90 cm and b=2 m. Oil a m b Water
3_Calculate the volume if it is v1=1.5 L, P1= 100 Кра, р2- 50 kpa.
2m Water. 20°C 4m He. 20 3m H.W3 water in a tank is pressurized to 85cmHg as show in Fig. Determine the hydrostatic forces per meter width on panel AB? note: Ans: =501 KN
A B с OIL WATER 1.0M 0.5m In the tank open to the atm. shown in the figure below, there is on oil layer 1 meter high on a 0.5 meter high water layer. Since pont & is in the Middle of paints A and C. calculate the pressures at points A, B, C, D in Kla. (Density of water 1000 kg/m³, density of oil 800 kg/m³)
If the Pressure in container A is 250 KPa, compute the Pressure in B. dto to 16 cm Hood - 8 cm To Water Oil, SG=0.8 Mercury hal 18 cm 22 cm Jos et tud inite di to
An open tank contains 5.6m of water covered with 3.4m of kerosene (S.G=0.80). Find the pressure at the interface and at the bottom of the tank