Q2: For the cantilever retaining wall shown below, calculate the factor of safety with respect to overturning, sliding, and bearing capacity. The required data are listed below: Wall dimensions: H=8.0m, x1=0.4m, x2-0.6m, x3=1.5m, x4-3.5m, x5=0.96m, D=1.75, a=10.0° Soil properties:y=16.5 kN/m', o'=32°,"y:=17.6 kN/m², o';=28°, c';=30 kPa.

Q2: For the cantilever retaining wall shown below, calculate the factor of safety with respect to overturning, sliding, and bearing capacity. The required data are listed below: Wall dimensions: H=8.0m, x1=0.4m, x2-0.6m, x3=1.5m, x4-3.5m, x5=0.96m, D=1.75, a=10.0° Soil properties:y=16.5 kN/m', o'=32°,"y:=17.6 kN/m², o';=28°, c';=30 kPa.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter17: Retaining Walls

Section: Chapter Questions

Problem 17.7P

See similar textbooks

Similar questions

For the retaining wall shown in the figure, determine the factor of safety against overturning and evaluate the result. The unit weight of the concrete is 150 pcf. 1.3 ft y = 115 pcf $ = 270 C = 0 12 ft y = 105 pcf 2 ft $ = 22° C = 400 psf 1.3 ft 5 ft
1. Calculate the maximum soil pressure. 2. Calculate the minimum soil pressure. 3. Design the spacing of the main reinforcement of the stem section of retaining wall using 28 mm diameter bar. Consider a load factor of 1.6, clear concrete cover of 75 mm and 12 mm diameter bar ties. Round off to whole number in mm.
A rectangular footing 2 m x 3.3 m x 0.36 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 313 kN LL = 244 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
As a Consulting Professional Engineer, you are required to provide a complete detailed structural design/analysis for the R.C. Wall specified in the following project problem under the "NEW" Loadings condition, and the new section-as specified below: "Design the reinforced concrete wall shown if fc' = 4000 psi and fy = 60,000 psi". %3D By changing the Horizontal Load to 200K, H=14 ft and L=14ft. 10 in. V, = 300 k h, = 12 ft 0 in. lw = 12 ft 0 in.
A rectangular footing 2.1 m x 3.7 m x 0.32 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 373 kN LL = 287 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the ultimate punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
Consider the MSE retaining wall shown below. Assuming that the reinforcement is a geotextile fabric with TULT = 10500 lbs/ft. Only consider internally stability. Do not check external stability. Assume that the backfill material and the native foundation soil have nearly identical soil properties: = 31° and y = 130 pcf. Evaluate the wall at 2 ft, 10 ft, and 20 ft below the retained ground surface. Determine the most appropriate vertical spacing (Sv) and total length of the reinforcement needed for the wall considering the requirements at each depth. Hi = 22 ft and H2 = 3 ft. H1 :- H2
PROBLEM 1 Discuss how will the compressive strength of concrete affects the area of main reinforcement and the flexural strength of the beam. PROBLEM 2 A 400mm concrete wall supports a DL= 200 kN and a LL = 146 kN. The allowable bearing pressure is 216 KPa at the bottom level of the footing which is 1.2m below the grade line. Weight of concrete is 24 kN/m and the soil is 16 kN/m3. Thickness of footing is 300mm with effective depth of 225mm. Determine and discuss the following: (a) Effective soil pressure (b) Width of the wall footing (c) Nominal shear force of the footing
A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 346 kN LL = 231 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA. Answer: 1.83
A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 346 kN LL = 231 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA. Selected Answer: O 1.92 Correct Answer: 1.83 ±0.01
3. If a wall has a total height of 4m and a width of 25 ft, find the number of 10 by 20 by 40 cm CHB, the horizontal reinforcement at every 2 layers and its vertical reinforcement spaced at 60 cm on center. Commercial length of = 10 mm ø by 9.0 m (Use Area Method and Unit Block Method) steel bar
29 A square footing 2.2 m x 0.39 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 317 kN LL = 217 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal one way shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
a rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 385 kN LL = 292 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal punching shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.