Q2. For the given single-phase full-bridge inverter in Fig. 1, assume Voj= 220V (rms) at a frequency of 47 Hz and the load is induction motor load with L=100mH. If the inverter is operating in a square-wave mode, calculate the peak value of the ripple current in the output. Induction-motor load Single-phase inverter UL = UL1 + Uripple iripple Urippie L Va Uripple (a) (e) ULI I jla,L) b1 = VL1 Vol (b) (d) Fig. 1. Single-phase inverter: (a) circuit, (b) fund. freq. components, (c) ripple freq. components (d) fund. freq. phasor diagram

Q2. For the given single-phase full-bridge inverter in Fig. 1, assume Voj= 220V (rms) at a frequency of 47 Hz and the load is induction motor load with L=100mH. If the inverter is operating in a square-wave mode, calculate the peak value of the ripple current in the output. Induction-motor load Single-phase inverter UL = UL1 + Uripple iripple Urippie L Va Uripple (a) (e) ULI I jla,L) b1 = VL1 Vol (b) (d) Fig. 1. Single-phase inverter: (a) circuit, (b) fund. freq. components, (c) ripple freq. components (d) fund. freq. phasor diagram

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. A single -phase full-bridge inverter is operated from a 48 V battery and is supplying power to a pure resistive load of 10 ohm. Calculate Fundamental component of the output voltage waveform First five harmonics of the output voltage waveform RMS value of the output voltage and output fundamental power i. ii. ii. Rating of SCR Verify the RMS value determined by harmonic summation method is nearly equal to the iv. v. value determined by integration method
Show that the THD of the phase voltage of the three-phase inverter square-wave mode is 0.31
Q1. The single phase half bridge inverter has a resistive load of R-24 9 and the de input voltage is Vs 48V. Draw the output voltage and drop voltage across the each switch, then, calculate (a) the rms output voltage at the fundamental frequency Vol (b) The output power Po (c) the average and peak currents of each transistor (d) the THD and (e) the HF and DF of the LOH 02 A) Drau
Q1. The single-phase half-bridge inverter in the figure below is switched on to generate a complete square voltage at the output. In this circuit, E = 160V and RL load with specifications of R voltage frequency is 50HZ. Then what is the THD output voltage percentage%? 10 ohms and L= 20mH. If the output E/2 LR E/2 Answer
Q2 (a) A single-phase full-bridge square-wave voltage source inverter has R and L load of 25 n and 15 mH, respectively and the load is connected in parallel. The inverter output frequency is 50 Hz while the transistor switching scheme is complementary bipolar (i) Define the expression of the RMS output voltage at the fundamental frequency. (ii) If the fundamental output voltage is 240 Vrms, identify the required DC input voltage for the inverter. (iii) Calculate the instantaneous load current by considering until the 7th harmonics number. (iv) Sketch the harmonic spectrum for output current. 2
A three phase inverter has a Y-connected load. The inverter frequency is fo= 60 Hz and the DC input voltage Vi = 220V. The applied control signal is a 120 deg conduction mode. The RMS magnitude of the fundamental VL1 is equal to 171.53V, then the HF and DF of the Lowest Order Harmonic LOH are equal to: Select one: Oa. 12% and 0.48% b. 20% and 0.8% O c. None of these O d. 20% and 4%
Find the RMS voltage expression of output phase voltage of a balanced three-phase square wave inverter need it asap
4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) a) Draw the circuit b) Plot the load current, showing the load voltage and semiconductor currents. c) Load voltage is effective calculate the value d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage
The input network voltage of the 1-phase bridge type rectifier was measured as 220 2 V peak. If the trigger angle is selected as 110 degrees, which of the following statements is correct? A) The average value of the output voltage is positive and is about 88.6 V. B) The average value of the output voltage is negative and about 127.3 V. C) The inverter is not in mode. D) The average value of the output voltage is negative and about 67.7 V. E) None
In a full-bridge single-phase inverter with an input voltage of 200V and a switchingfrequency of 4kHz, the power of a 16Ω load is controlled by the method of a gappedsquare wave control. Ignoring the circuit losses, answer the following questions A) Find the nominal (the maximum) power and current of the load B) Find the duty ratio to get half of the nominal voltage C) Find the duty ratio to get a quarter of the nominal power D) Find the average value and effective value of BJT current for the case of item-e
The load voltage waveform of a single phase full bridge inverter supplied from 30OV DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load vahues are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition c. Find the RMS values of the load voltage and the load current d Calculate and draw the voltage across the load inductance e. Calculate and draw the source current and find its average vahue
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition