Q3: Tikrit University has been implemented a project of an electrical portable station. This project includes installing two towers each of them has a hight of 39 m to cary the overhead transmission line from outside to inside the University. And the distance between the towers is 300 m. But, the transmission line flow-through a ground has a gradient (slope) of 1/15. After calculating the sag, find the distance (clearance) between the orginal point and the ground. The tensile strength in the wire is 2500 N/cm2. The weight of one meter of the conductor is 9 N. The cross-section area of the conductor is 4 cm2.

Q3: Tikrit University has been implemented a project of an electrical portable station. This project includes installing two towers each of them has a hight of 39 m to cary the overhead transmission line from outside to inside the University. And the distance between the towers is 300 m. But, the transmission line flow-through a ground has a gradient (slope) of 1/15. After calculating the sag, find the distance (clearance) between the orginal point and the ground. The tensile strength in the wire is 2500 N/cm2. The weight of one meter of the conductor is 9 N. The cross-section area of the conductor is 4 cm2.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.27P: Figure 4.34 shows double-circuit conductors' relative positions in segment I of transposition of a...

See similar textbooks

Similar questions

Transmission line conductance is usually neglected in power system studies. True False
400Ω A k=0.9 600Ω B k=0.8 66Ω 600Ω
Problem: A three phase transmission line is being supported by 3 disc insulators. The potential across top unit (near the tower) and middle unit are 8 kV and 11 kV respectively. Determine; i) ratio of capacitance between pin and earth to self capacitance of each unit, ii) the line valtage and iii) string efficiency.
Q2(a) Figure Q2(a) shows the spacing of a double circuit 3-phase overhead line. The phase sequence is UVW and the line is completely transposed. i) Critically assess the advantages of double circuit line over single circuit line Calculate the inductance per phase for 500 meter length of line using Table 2(a) data for the Figure Q2(a). Table 2(a) GMR of the line 0.01m Distance a-b' 6.m Distance c-c' 8.3m a b Figure Q2(a)
Describe the effect of resistive load on sending and receiving end voltages, Power transferred and Power factor.
(a) A three phase transposed transmission tower comprises of three-bundled conductor and double-circuit configured in vertical position as shown in Figure 2. Each sub-conductor in each circuit and each phase is an ACSR type, size 477,000 cmil and stranding 26/7. Given the GMR of each sub-conductor is 0.8809 cm and diameter is 2.1793 cm, analyze: i. Inductance in mH/km ii. Capacitance in µF/km 0.75m 7.5m b' 4m 4m 45cm Figure 2
The equivalent circuit of a single phase short transmission line is shown in Figure Q4 (b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4 (b) for the lagging power factor at load point (Vn). ii) Summarize, the impact of voltage regulation and efficiency, if the line resistance and line increases are doubled Figure Q4(b). R XL Vs Vn Figure Q4(b) Load
iv. For a long high voltage transmission line with light loading : (a) The voltage is generally high due to reactive power generated by the line. (b) The voltage is generally high due to the light loading. (c) The voltage is generally high due to high reactive power generated and the low reactive power consumed by the line.
Q4(b) The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4(b) for the lagging power factor at load point (Vn). ii) Summarize, what if the load change from low value to high value shown in Figure Q4(b). R XL el Vs Vn Figure Q4(b) Load
Consider the following statements: Surge impedance loading of a transmission line can be increased by 1. increasing its voltage level 2. addition of lumped inductance in parallel 3. addition of lumped capacitance in series 4. reducing the length of the line Which of these statements are correct? (a) 1 and 3 (b) 1 and 4 (c) 2 and 4 (d) 3 and 4
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A bipolar HVDC link is delivering 1000 MW at ±400 kV at the receiving end. Calculate the losses in the line, assuming the resistance per conductor as 1 2. Also estimate the sending end power, sending end voltage, power in the middle of the line, and line losses. Ans:=PLosses = 3.75 MW, P,= 1003.75 MW, V401.25 kV, P=1001.562 MW