Q31 In the mechanism shown in Fig (3), the slider C A is moving to the right with a velocity of (1 m/s) and an acceleration of (2.5 m/s?). The dimensions of various links are (AB= 3 m) inclined at (45°) with the vertical, and (BC= 1.5 m) inclined at (45°) with the horizontal. 45° 3 m B 45° 1.5 m Determine: a- The angular velocity (w) of the links AB and BC. b- The angular acceleration (a) of the links AB and BC, to

Q31 In the mechanism shown in Fig (3), the slider C A is moving to the right with a velocity of (1 m/s) and an acceleration of (2.5 m/s?). The dimensions of various links are (AB= 3 m) inclined at (45°) with the vertical, and (BC= 1.5 m) inclined at (45°) with the horizontal. 45° 3 m B 45° 1.5 m Determine: a- The angular velocity (w) of the links AB and BC. b- The angular acceleration (a) of the links AB and BC, to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rollers attached to rod AB can slide freely along the horizontal floor and the vertical plane. At the instant shown, end A has a downward velocity of 2.5 ft/s. Determine (a) the angular velocity of the rod and (b) the velocity of end B of the rod. A В 12 in 20 in 16 in
I. For the frame shown (AN 15), the force F acting upward at C causes a horizontal reaction of 100 kN at C. Which of the following most nearly gives 1) The value of the force F in kN, 2) gives the reaction at A in kN, 3) the angle in degrees that the reaction at A makes with the horizontal axis (positive counterclockwise). 5 m Figure AN-15
(Situation no. 2) For the beam supporting the loads shown with E= 200000 Mpa and I=1x10^8 mm^4. (4) Determine the reaction at the roller support, in KN. (5) What is the value of the deflection at point B, in mm? (6) What is the slope at C, in degrees? 8KN/m B 4m 4m Select the correct response: 24.50 kN 18.50 kN O 20.50 kN O 16 kN TTTTI
4. Determine the reactions at A and B when a = 150 mm. 500 N 240 mm В ATVS
Q2/: The angular velocity of rod AB is 20rad/s clockwise. For the instant shown, determine: 2.1. The angular velocity of rod BD, 2.2. The velocity of the midpoint of rod BD. A 0.2 m 0.25 0.2 m 0,6 m
The beam is loaded and supported as shown in the figure, find the reaction at roller support. (kN 48.19 10KN/m 15KN 10kN/m ideg C. 2m 2m 1m 20kNm
Situation A 4- a particle rotates in accordance with the equationd= 24-6t, where & is in rad/s? ard t is in secs. when t=0,w-20 rads/s ard + =0. Find the maximum angular velocity - %3D
团の image.jpg > B00 Deker mine the magni nde mnd direction 200 of the resultant +300 of the four forces shown in the higure. 420 500 Determine the moment a bout Point as Shown
Q/ The (200N) block shown in Fig . Has impending motion up the plane .Coused by e isjall dåg le the Horizontal force Lii 5 gå of ( 400N ). Determine the coefficient of static friction between the contact surfaces alial l. 400N 200N 300
Activity 1: Determine the angle e for equilibrium of the lever shown in the figure. Disregard the weights of bars AB and BC. 2m 90 1m, A 200N 100N Activity 2: Determine the weight W and the horizontal and vertical components of the pin reaction at A for equilibrium assuming all bearings are frictionless. Beam AB weighs 600 KN. 800KN 400KN 3m 1m 2m 1600N/m Ap 6m
Q5. A simply supported girder of span 3.5 m and mass 87.5 kg was subjected to a concentrated impulsive force at mid span. In the free damped oscillation which followed, the ratio of two successive amplitudes of the girder at centre was 1.3. Calculate the time taken for the amplitude of vibration to decay to (1/50)th of initial displacemen Given, l= 2290cm4; E= 200kN/mm². Also compute the coefficient of damping.
If bar AB has an angular velocity w AB = 4 rad/s, determine the velocity of the slider block C at the instant shown. 30° 200 mm B 150 mm WAB = 4 rad/s 60°