Q3//A// Peak demand of generating station is 90MW and the load factor is 0.6. The plant capacity factor and plant use factor are 0.5 and 0.8 respectively. Determine (a) daily cnergy produced; (b) installed capacity of plant; and (c) reserve capacity of plant. B/A 60 MW steam power station has a thermal efficieney of 30% If the coal burnt has a calorific valuc of

Q3//A// Peak demand of generating station is 90MW and the load factor is 0.6. The plant capacity factor and plant use factor are 0.5 and 0.8 respectively. Determine (a) daily cnergy produced; (b) installed capacity of plant; and (c) reserve capacity of plant. B/A 60 MW steam power station has a thermal efficieney of 30% If the coal burnt has a calorific valuc of

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is............... percent. *
5. Draw the daily load curve and load duration curve for a power station with any arbitrary loads you like. From the load curve, determine the following. i. Maximum demand ii. Average demand ii. Daily energy consumption
2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
1. Find the required single-phase excitation voltage at rated voltage and frequency, in Volts 2. Find the required single-phase excitation voltage when both terminal voltage and frequency are 80% of their rated values, in Volts
7. TY Hat CHICL Ans. 1. Iron los.........varies approximately as V². 2. Cu loss..........it also varies as ² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa. quems
OR e) What is BILS? Explain their significance in power system studies.
A generating station has a maximum demand of 20MW,a load factor of 60%, a plant capacity factor of 48%, and a plant use factor of 80%. Determine the reserve capacity of the plant.
A generating station has a maximum demand of 20 MW, a load factor of 60%, a plant capacity factor of 48% and a plant use factor of 80% Find: 1)the daily energy produced (2) the reserve capacity of the plant. (3) The maximum energy that could be produced daily if the plant was ruinining all the time.(4).Maximum energy that could be produced daily if the plant was running fully loaded and according to an operating schedule.
Load on a small power station is as under. Draw the load curve and calculate 1. Maximum demand 2. Units generated in a day 3. Average demand 4. Daily load factor.
Explain about the power production scenario and write down about the growth.
What effects are produced by change in voltage? 1. Iron los..........varies approximately as V². 2. Cu loss..........it also varies as V² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa.