04- Along hollow copper cylinder has its inner surface maintaincd at 150 C and is buried in amaterial having a thermal conductivity of 18 W/m C. The outer and the inner diameters of thecylinder are 5 and 3 cm respcctively, and the depth to its centerline is 15 cm. The surfacetemperature of the material is 25C,Based on ID conduction analysis, calculate the heat transfer from the cylinder per meter oflength.

Answered: Image /qna-images/answer/7885b5d0-733e-4fe0-9258-091d05220803.jpg

Q4- Along hollow copper cylinder has its inner surface maintained at 150-C and is buried in material having a thermal conductivity of 18 W/m C. The outer and the inner diameters of the cylinder are 5 and 3 cm respectively, and the depth to its centerline is 15 cm. The surface temperature of the material is 25 C, Based on ID conduction analysis, calculate the heat transfer from the cylinder per meter of Laneth

Q4- Along hollow copper cylinder has its inner surface maintained at 150-C and is buried in material having a thermal conductivity of 18 W/m C. The outer and the inner diameters of the cylinder are 5 and 3 cm respectively, and the depth to its centerline is 15 cm. The surface temperature of the material is 25 C, Based on ID conduction analysis, calculate the heat transfer from the cylinder per meter of Laneth

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.22P

See similar textbooks

Similar questions

1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
1.51 The inner wall of a rocket motor combustion chamber receives by radiation from a gas at . The convection heat transfer coefficient between the gas and the wall is . If the inner wall of the combustion chamber is at Problem 1.51 a temperature of , determine (a) the total thermal resistance of a unit area of the wall in and (b) the heat flux. Also draw the thermal circuit.
2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kD=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces.
1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
A ball made of steel alloy with a diameter of 2 millimeters is first heated to 800 degrees and then suddenly immersed in a water bath to cool down to 100 degrees. The materials from which the ball is made have a thermal conductivity coefficient of 54.94 w / mk, a heat capacity of 7860 kg / m3, a heat capacity of 450 j / kg. Also, the heat transfer coefficient is 41.66 2 / m2. a-)Find the temperature of the ball immersed in water after 10 seconds. b-)Find the time required to cool the ball to 400 degrees.
A bar with surface temperature (310) oC and diameter (9.5) mm, temperature 20oC and heat convectionIt is contained in a fluid with a coefficient of 95 W / m2K. The top of this bar is heat conductionIt is desired to be coated with bakelite with a coefficient of 2.5 W / mK up to the critical radius thickness.a) the critical radius of the bakelite coating and the heat transfer at the critical radius per unit length.Found it. b) heat transitions per unit length for uninsulated and bakelite (insulation) coated rodYou calculate. Comment the results
Choose the false statement? We can express lumped capacitance relation as the combination of Biot and Fourier numbers At very low values of Prandtl number, material has higher thermal conductivity compared to its momentum diffusivity We can calculate convective heat transfer coefficient from Nusselt number If Biot number is less than 0.1, we can neglect thermal resistance in some direction None of the given